Hoiatused
See veebileht loetleb OpenWrt süsteemi toetavate seadmete tarkvara, enne tarkvara allalaadimist ja paigaldamist palume arvestada, et OpenWrt Project on Linuxi operatsioonisüsteem, mis on suunatud manussüsteemidele. Selle asemel, et püüda luua üksikut staatilist püsivara, pakub OpenWrt täielikult kirjutatavat failisüsteemi koos paketihaldusega. See vabastab teid müüja poolt pakutavate rakenduste valikust ja konfiguratsioonist ning võimaldab teil kohandada seadet pakettide abil mis tahes rakendusele sobivaks. Arendajate jaoks on OpenWrt raamistik, mille abil saab luua rakenduse, ilma et oleks vaja ehitada selle ümber täielikku püsivara; kasutajate jaoks tähendab see võimalust täielikuks kohandamiseks, et kasutada seadet viisil, mida nad pole kunagi ette kujutanud.
Kirjeldus
- Seda faili saab kasutada ainult siis, kui teie ruuter töötab Cudy veebi kasutajaliidese all.
- Kui ruuter juba töötab OpenWRT UI all, peaks kasutaja esmalt taastama selle Cudy ametliku firmware'ile. Ja seejärel uuendada ruuterit selle püsivara abil.
- Kuidas taastada ruuter Cudy ametlikule püsivara? Palun lugege alla laaditud faili readme.
Garantii:
Cudy deklareerib käesolevaga
- Me, Cudy, ei võta garantiid ühegi tarkvara eest, mida ei ole välja andnud Shenzhen Cudy Technology Co., Ltd. .
- Me ei võta garantiid toodete eest, millele on paigaldatud tarkvara, mida ei ole välja andnud Shenzhen Cudy Technology Co., Ltd. .
- Kui teil on vaja kasutada openwrt tarkvara, soovitame selle alla laadida Cudy ametlikust veebisaidist.
Laadige alla OpenWrt püsivara, et eemaldada allkirja kontroll: Ajama
OpenWrt Firmware Finder (ei ole Cudy poolt välja antud): OpenWrt Firmware Selector
1531 kommentaari
Нужна промежуточная прошивка для репитера RE 3000 v1.0.
Hi, I have a Cudy WR3000H V1.0 with:
Stock firmware: 2.4.5-20250515-105059 (it came pre-installed).
I need the correct intermediate firmware to install OpenWrt on my WR3000H v1.0 (SN: WR3000H25430***** – new flash chip).
I tried flashing:
cudy_wr3000h-v1-sysupgrade_20251119.bin
The file from your official Google Drive (WR3000H 1.0.zip)
Both attempts failed with the same error at ~75%: “File is invalid. Please retry.”
Since my SN starts with 2543, I believe I need the intermediate firmware specifically for the new flash chip. Could you please send me the correct file and any special instructions?
I already emailed support@cudy.com requesting the correct OpenWrt intermediate firmware for this exact hardware revision, but I have not received a reply yet.
Could your technical support please check my email and send me the correct intermediate firmware compatible with this unit?
Thank you.
Best regards.
Hello,
Cudy M3000 V2.0, SN M3000244700186, board R37, flash F50L1G41LB (old flash), WAN PHY rtl8221b.
The intermediate firmware from your Drive (cudy_m3000-v1-sysupgrade_20251119.bin) is rejected: “File is not compatible with the device model” on stock 2.5.10, and “Incorrect firmware file” on stock 2.4.19. Could technical support send the intermediate firmware for this exact revision? I already emailed support@cudy.com.
@Dear Vince,
Our technical support has sent you the firmware via email. Please check.
“Hi, I have a Cudy WR3000H V1.0 with:
Stock firmware: 2.4.5-20250515-105059
Flash: ESMT F50L1G41LC
WAN PHY: Motorcomm YT8821
I already emailed support@cudy.com requesting the correct OpenWrt intermediate firmware for this exact hardware revision, but I have not received a reply yet.
Could your technical support please check my email and send me the correct intermediate firmware compatible with this unit?
Thank you.”
Hi, I have a Cudy WR3000H V1.0 with:
Stock firmware: 2.4.5-20250515-105059
Flash: ESMT F50L1G41LC
WAN PHY: Motorcomm YT8821
I already emailed support@cudy.com requesting the correct OpenWrt intermediate firmware for this exact hardware revision, but I have not received a reply yet.
Could your technical support please check my email and send me the correct intermediate firmware compatible with this unit?
Thank you.