OpenWrt tarkvara allalaadimine

Hoiatused

See veebileht loetleb OpenWrt süsteemi toetavate seadmete tarkvara, enne tarkvara allalaadimist ja paigaldamist palume arvestada, et OpenWrt Project on Linuxi operatsioonisüsteem, mis on suunatud manussüsteemidele. Selle asemel, et püüda luua üksikut staatilist püsivara, pakub OpenWrt täielikult kirjutatavat failisüsteemi koos paketihaldusega. See vabastab teid müüja poolt pakutavate rakenduste valikust ja konfiguratsioonist ning võimaldab teil kohandada seadet pakettide abil mis tahes rakendusele sobivaks. Arendajate jaoks on OpenWrt raamistik, mille abil saab luua rakenduse, ilma et oleks vaja ehitada selle ümber täielikku püsivara; kasutajate jaoks tähendab see võimalust täielikuks kohandamiseks, et kasutada seadet viisil, mida nad pole kunagi ette kujutanud.

Kirjeldus

  1. Seda faili saab kasutada ainult siis, kui teie ruuter töötab Cudy veebi kasutajaliidese all.
  2. Kui ruuter juba töötab OpenWRT UI all, peaks kasutaja esmalt taastama selle Cudy ametliku firmware'ile. Ja seejärel uuendada ruuterit selle püsivara abil.
  3. Kuidas taastada ruuter Cudy ametlikule püsivara? Palun lugege alla laaditud faili readme.

Garantii:

Cudy deklareerib käesolevaga

  1. Me, Cudy, ei võta garantiid ühegi tarkvara eest, mida ei ole välja andnud Shenzhen Cudy Technology Co., Ltd.
    2. .
  2. Me ei võta garantiid toodete eest, millele on paigaldatud tarkvara, mida ei ole välja andnud Shenzhen Cudy Technology Co., Ltd.
    3. .
  3. Kui teil on vaja kasutada openwrt tarkvara, soovitame selle alla laadida Cudy ametlikust veebisaidist.

Laadige alla OpenWrt püsivara, et eemaldada allkirja kontroll: Ajama

OpenWrt Firmware Finder (ei ole Cudy poolt välja antud): OpenWrt Firmware Selector

Tagasi blogi juurde

1530 kommentaari

Hello.

I have a Cudy WR3000 V1.0 router.

Serial number starts with: 2532

Current stock firmware: 2.4.19-20250828-192837

I would like to install official OpenWrt.

Please send me the latest Cudy-signed OpenWrt intermediate firmware compatible with my WR3000 V1.0 and this hardware/flash revision.

Thank you.

Vadim

Hello,

I have a Cudy WR3000 V1.0 EU router.

Serial number starts with: 2539
Current stock firmware: 2.4.19-20250828-192837

I would like to install official OpenWrt.

Please send me the latest Cudy-signed OpenWrt intermediate firmware compatible with my WR3000 V1.0 and this hardware revision.

Thank you.

NN

Greetings,
I would like to request for the signed openwrt firmware for M3000 with a Motorcomm YT8821 (Variant 2) please.
Thanks

Davis

@Dear Mike,
The firmware file in Google Drive is correct. This is for both hardware version. Please unzip the file before update.
Note: If you have installed Mesh system with the router. You can’t update the firmware. Please power off the other Mesh device. Then reset this router to factory default. You can update this firmware before mesh system installed.

“Hi,
I would also like to request the M3000 V.2 with the Motorcomm YT8821 chip, if that’s possible.
Thank you.”

support

@Dear Горбунов Михаил,
I think there is some hardware faulty in the router. You can try to contact the seller to request a replacement and try again.

“Hello. I specifically need to install OpenWrt on a Cudy M3000 V2.0. The current issue is not simply with the stock firmware, but with the OpenWrt installation process and the intermediate firmware file.

The situation is as follows:

Router: Cudy M3000 V2.0
I used the intermediate firmware file intended for transitioning from the stock Cudy firmware to OpenWrt.
After flashing that intermediate file, the router does not boot into OpenWrt correctly.
The Ethernet connection periodically goes down and comes back up.
The router appears to enter a reboot/boot loop, with the LED changing states.
There is no stable access to OpenWrt at 192.168.1.1.
Sometimes 192.168.10.1 becomes available again.

So my goal is not just to restore the stock firmware. I need to successfully complete the installation of OpenWrt.

Could you please clarify:

After flashing your intermediate file, should the M3000 V2.0 boot directly into OpenWrt?
If yes, why might my router be entering a boot loop instead of booting OpenWrt?
Is another firmware file required after the intermediate file?
If so, which exact OpenWrt image should be used for Cudy M3000 V2.0?
Should it be a factory.bin, sysupgrade.bin, or a special recovery/install image?
If the next step must be performed via TFTP, please provide the exact procedure:
required filename;
PC IP address;
router IP address;
which LAN port to use;
RESET/power-on sequence;
which firmware image should be transferred.
Could this problem be caused by the intermediate firmware itself or by a specific hardware revision of the M3000 V2.0?

What I need is a working step-by-step procedure for installing OpenWrt on the M3000 V2.0 from its current state, because at the moment the intermediate firmware does not result in a successful OpenWrt boot.

If necessary, I can provide a video of the boot loop, ipconfig/ping output, and the current stock firmware version."

support

Jäta kommentaar