1. Laadige fail alla ja pakendage see hinnast.
2. Laadige uusim püsivara ametlikust veebisaidist ja nimetage see ümber "recovery.bin". Märkus: Te peate selle panema samasse faili Tftpd tööriistade hulka.
3. Lülitage ruuter välja. Tõmmake toiteadapter välja või vajutage nuppu POWER.
4. Ühendage arvuti ruuteri LAN-porti Ethernet-kaabliga.
5. Konfigureerige oma arvuti IP-aadressi '192.168.1.88' käsitsi.
6. Käivitage 'tftp32.exe'.
7. Käivita käsureas 'netsh advfirewall set allprofiles state off', et keelata Windowsi tulemüür, muidu blokeeritakse tftp. Või lülitage tulemüür välja oma arvuti juhtpaneelis. Nagu allpool näidatud.
8. Vajutage nuppu/auku "Reset" ja hoidke seda all. Enne ruuteri sisselülitamist ja enne, kui tftp alustab püsivara allalaadimist, ärge vabastage nuppu 'Reset' / auku.
9. Lülitage ruuter sisse.
10. Kui kõik tuled vilguvad kiiresti või kui tftp hakkab püsivara alla laadima, võite vabastada nupu 'Reset' nuppu/auku.
11. Kui tuli vilgub aeglaselt, on uuendamine lõpetatud.
12. Taastage oma arvuti IP-aadress dünaamiliseks IP-ks.
13. Valmis.
264 kommentaari
@Dear Ricci,
If you have changed the uboot of the router. This recovery method will not work. You must change back the default Cudy uboot first to recover the firmware.
“Hello again, I have already written a comment here in search of a solution to my problem. I have a cudy tr30 router model, I installed the openwrt firmware on it according to the YouTube guide and after the power was turned off, the firmware stopped loading, I tried everything except using UART, today I’ll probably try to figure it out with chat gpt, but if you have another easier way to get the cudy tr30 firmware back, then I I would be very grateful.”
WR3600H version 1.0 — blocked after flashing the intermediate firmware
Hello, Cudy support service,
I have a Cudy WR3600H version 1.0
Serial number: WR3600H244300255
What happened:
I updated the router to the official firmware 2.5.30 via tftpd64
Please help me restore the router.
Thank you.
TR3000 256MB V1.0 — bricked after flashing intermediate firmware
Hello Cudy Support,
I have a Cudy TR3000 256MB Flash V1.0 router.
Serial number: s0001825262604247
What happened:
I updated the router to the official firmware m_upgrade_TR3000_256MB_Flash-R103-2.5.21-20260708.
After that, I downloaded the intermediate firmware DTS_and_intermediate_firmware_b766f42b-5e1c-4ad5-85b2-53990a85a956 from the TR3000-256MB 1.0 download page.
I flashed this intermediate firmware through the web interface.
After the flash, the router does not boot. It is bricked.
What I need:
The correct TFTP recovery file (recovery.bin) for my specific device.
Step-by-step TFTP recovery instructions for TR3000 256MB V1.0.
Confirmation of which flash chip is installed in my unit (F50L1G41LB or F50L1G41LC).
The correct intermediate firmware for my device revision to install OpenWrt, if my unit has the new flash chip.
Please help me recover the router.
Thank you.
Hello again, I have already written a comment here in search of a solution to my problem. I have a cudy tr30 router model, I installed the openwrt firmware on it according to the YouTube guide and after the power was turned off, the firmware stopped loading, I tried everything except using UART, today I’ll probably try to figure it out with chat gpt, but if you have another easier way to get the cudy tr30 firmware back, then I I would be very grateful.
@Уважаемый Евгений,
Спасибо за отзыв.
“В модели WR300 необходимо не зажимать кнопку, а при подаче питания несколько раз нажать.”