WISP-režiim:
WISP-režiimis võimaldab ruuter mitmel kasutajal jagada WISPi internetiühendust. LAN-pordi seadmed jagavad sel viisil WISPist sama IP-d juhtmevaba pordi kaudu. WISPiga ühendatuna toimib traadita port nagu WAN-port.
Üldine võrgutopoloogia:
Sepp 1: Avage veebilehitseja ja minge http://cudy.net või http://192.168.10.1.
.Detailide saamiseks vaadake Kuidas sisse logida Cudy Routeri veebiliidesesse?
Samm 2: Es avaneb Quick Setup aken, valige "WISP", seejärel minge "Next".
Samm 3: Valige oma "Ajavöönd".
Sepp 4: Valige host-võrk, mida soovite laiendada. Vajutage nupule 'Connect'.
Või klõpsake Üldised sätted->WISP->Enable ja seejärel valige hostivõrk, mida soovite laiendada.
Sepp 5: Esita host-võrgu traadita võrgu parool.
Note: Vajuta, et sisestatud traadita parool oleks õige, vastasel juhul ei saa konfiguratsioon õnnestuda.
Sammu 6: Muuta traadita võrgu nimi ja parool või jäta need vaikimisi.
Sammu 7: Klikkige "Save & Apply", et lõpetada konfiguratsioon.
Sepp 8: Oota paar sekundit süsteemi taaskäivitamiseks, kui sisselogimisleht taas avaneb, võid nautida internetti.
114 comments
Hello Cudy Support. Could I also get please the beta version of Firmware supporting WISP work mode for the WR6500H router?
Thx
@Dear Peter Tomaščík,
Our technical support has sent you the firmware via email. Please check.
“I recently purchased the Cudy WR6500 as an upgrade to my older Cudy WR3000. My original plan was to use the new WR6500 as my main router and repurpose the WR3000 as a Mesh node to extend my network coverage.
However, I ran into a major issue: the WISP mode is missing in the WR6500 settings, whereas it works perfectly fine on the older WR3000.
Because the WR6500 lacks WISP support, I am currently forced to use it only as a Mesh extension instead of the main router, which completely degrades its performance and defeats the purpose of the upgrade.
Could the support team or anyone here provide me with a firmware version for the WR6500 that includes the WISP functionality?”
@Dear Lawson,
Please go to “General Settings” —"WISP " function page to set it up.
“I have the 4GvLTE N300 V3.0
I’ve got firmware 2.5.12 installed, but still no WISP
Could you send me the firmware that allows for Wisp please. I’m happy to test it if it’s Beta.”
@Dear John,
I think yes. WR1200 supports WISP function to connect the main Wi-Fi via wireless. But you must check if the signal strength starlink mini wifi router at the placement of WR1200 is powerful enough to connect to?
“Hi, can I use the wr1200 to feed wired internet into my lan from a starlink mini wifi router. I would like to not have a wire from the starlink into my existing lan which covers 4 floors of a concrete building. Is this compatible.
Thank you.”
I recently purchased the Cudy WR6500 as an upgrade to my older Cudy WR3000. My original plan was to use the new WR6500 as my main router and repurpose the WR3000 as a Mesh node to extend my network coverage.
However, I ran into a major issue: the WISP mode is missing in the WR6500 settings, whereas it works perfectly fine on the older WR3000.
Because the WR6500 lacks WISP support, I am currently forced to use it only as a Mesh extension instead of the main router, which completely degrades its performance and defeats the purpose of the upgrade.
Could the support team or anyone here provide me with a firmware version for the WR6500 that includes the WISP functionality?