Cudy Whole Home Mesh system is built to eliminate dead zones and to provide uninterrupted Wi-Fi throughout your home. This article will guide you to build a mesh system step by step.
Preparation:
1. Ensure you own at least 2 Cudy products.
2. All Cudy products support mesh technology: Home Mesh-Cudy official website
3. Firmware is up-to-date: Download Center
4. Take them in the same room during configuration.
5. Reset all your Cudy products to factory default settings. (With the Power on, press and hold the RESET button with a pin for 6s, then release.)
6. Set up your primary router and make it connect to the internet.
Here we take M1800 and WR2100 as examples:
Step 1: Open a web browser and go to http://cudy.net or http://192.168.10.1.
For details, please refer to How to log into the web interface of Cudy Router?
Step 2: On the System Status page, click on the "+" button.
Step 3: Press the WPS button on the M1800 and then press the WPS button on WR2100.
Main mesh unit: Flash white
Add-on mesh unit: Flash white and red alternately
Step 4: It will go to "Scanning", then " Connecting".
Step 5: Wait until the System LED of the add-on router turns into solid blue, then relocate WR2100.
Step 6: Success and enjoy the mesh network.
Note:
1. 4/5G router can only be set up as a Main mesh unit. For example:
2. You will not able to log into the web interface of the add-on mesh router. If you want to change settings, please click on "System Status"->"Mesh".
71 comments
@Dear Gabriel,
Basically, this is a hardware issue. May be caused by the cable or the router. We can have a compare test. You can choose one of the other two routers, Reset it and set it to be the main mesh router and connect to the same cable to check if it work on 1 Gbps or 100Mbps to judge the root cause.
“Dear Cudy Support,
I recently purchased a Cudy AX3000 Gigabit WiFi 6 Mesh Router along with two additional AX3000 mesh units, all of which support gigabit Ethernet ports.
My internet plan provides 200Mbps, and I am using undamaged Cat 6 Ethernet cables. The main router is connected to one of the mesh nodes via Ethernet. Up until yesterday, everything was working perfectly—I was getting full gigabit speeds through the LAN ports.
However, after rebooting the entire system today, the main router’s Ethernet ports are now only delivering 100Mbps. I’ve confirmed that the cables are properly seated and not damaged, and the same setup was previously delivering full gigabit speeds without issue.
Could you assist in identifying what might have caused this and how to resolve it?
Thank you"
Dear Cudy Support,
I recently purchased a Cudy AX3000 Gigabit WiFi 6 Mesh Router along with two additional AX3000 mesh units, all of which support gigabit Ethernet ports.
My internet plan provides 200Mbps, and I am using undamaged Cat 6 Ethernet cables. The main router is connected to one of the mesh nodes via Ethernet. Up until yesterday, everything was working perfectly—I was getting full gigabit speeds through the LAN ports.
However, after rebooting the entire system today, the main router’s Ethernet ports are now only delivering 100Mbps. I’ve confirmed that the cables are properly seated and not damaged, and the same setup was previously delivering full gigabit speeds without issue.
Could you assist in identifying what might have caused this and how to resolve it?
Thank you
@Dear Walter,
Yes, you can. The Cudy APs, such as the AP3000 and AP1300 can work as the main mesh device to manage other APs. You can set up one of the AP3000 and connect it to the network. Then connect other AP to the network. The mesh system will be installed automatically.
“Can I set up a mesh network using only Cudy AP’s? I have a different brand router so I want to build a mesh network with just the AP’s”
Can I set up a mesh network using only Cudy AP’s? I have a different brand router so I want to build a mesh network with just the AP’s
@Dear Carlos,
Our technical support has sent you the firmware of WR6500 via email. Please check.
“Hello, I have a BE3600 and a BE 6500 but i cant connect them with mesh, be3600 has the firmware updated but 6500 doesnt”