准备：
1. 安装天线并将其向上放置。
2. 将 SIM 卡插入插槽，直至听到咔嗒声。
3.将电源适配器连接到路由器并打开电源。
步骤1：打开浏览器，访问http://cudy.net或http://192.168.10.1 ，输入管理员密码登录。
注意：如果固件版本为 1.XX，则默认管理员密码为“ admin ”自固件版本 2.XX 以来，我们已删除默认管理员密码 首次登录时必须创建管理员密码。
详情请参考如何登录Cudy路由器的Web界面？
第 2 步：快速设置窗口将会弹出，选择您的“时区” 。
步骤3：配置APN参数。通常情况下，我们只需将APN配置文件保留为“自动”即可。然后点击“下一步”。路由器会自动选择APN参数。（推荐）
如果您想自定义APN参数，您可以选择APN配置文件为“手动”，并输入正确的APN参数。
注意：如果您不确定 APN 参数，请联系您的互联网服务提供商。
步骤4：设置无线网络名称和密码或保持默认。
步骤5：点击“保存并应用”完成配置。
步骤6：当状态为已连接时，您就可以享受互联网了。
52 条评论
@Dear Sakai,
You can set the metric of the WAN connection. The small the metric, the higher priority the WAN connection.
For the new firmware, it is under development currently. We will release a new firmware in the near future.
“R700 V1.0
I bought this router recently and this has never received any firmware update since its release date. Can you guys work on its latest firmware? Currently, we are unable to put multiple IP ranges when making a rule set to route specific data through a specific WAN.
Also, the rule is not applying properly sometimes. In the policy tab, you can not give priority to a specific WAN. Please fix these."
R700 V1.0
I bought this router recently and this has never received any firmware update since its release date. Can you guys work on its latest firmware? Currently, we are unable to put multiple IP ranges when making a rule set to route specific data through a specific WAN.
Also, the rule is not applying properly sometimes. In the policy tab, you can not give priority to a specific WAN. Please fix these.
@Dear Tommy,
Generally, there is no need to set the router. Just connect the devices to the LAN ports of the router. Then it will work. You can try to reset the router to factory default by long pressing the reset button for about 3 seconds. You can release the reset button when the LED flashes. Then connect all the devices and check if the problem avoided?
In addition, please check if the CCTV camera is set to get the IP address via DHCP when connect to the router via wired cable? If not, please set it.
“Dear Cudy team. How should I configure your router lt500D to be able to connect two CCTV cameras via Ethernet cable? I was able to connect only one that supports wifi, second one can be connected only via cable. Your router does not see these devices in lan network.”
Dear Cudy team. How should I configure your router lt500D to be able to connect two CCTV cameras via Ethernet cable? I was able to connect only one that supports wifi, second one can be connected only via cable. Your router does not see these devices in lan network.
@Dear Amigos,
The AT command for checking EARFCN is AT+QENG=“servingcell” , You can also check it in the syslog. For example
AT+QENG=“servingcell” → AT+QENG=“servingcell” +QENG: “servingcell”,“NOCONN”,“LTE”,“FDD”,250,01,41720C,9,1802,3,5,5,454C,-89,-10,-59,14,35 OK
The “1802” is the EARFCN.
For cell ID, we don’t have plan to change the format.
“Hi! In first iam need to say thanks for very balanced products with Cudy brand. Anyway i have some question about Cudy LT400 Outdoor functions.
1 – in Status we have data about LTE connection as MCC MNC CID and PCID, but not EARFCN and not eNodeB ID. How i can get it? Modem have this data by cell.
2- Cell ID have hex format. possible convert it in dec format Base ID?
and very important
need AT commands LIST for internal modem.
Thanks!"