Güncelleme: 24 Aralık 2025 İyi haber!
OpenWrt forumu, yeni Flash F50L1G41LC'yi destekleyen ve OpenWrt ürün yazılımını 24.10.5 sürümüne güncelleyen yamayı birleştirdi. Bu nedenle, gelecekte Cudy ile ilgili modelleri güncellemek için OpenWrt ürün yazılımının 24.10.5 veya daha yeni bir sürümünü indirirseniz, herhangi bir sorun yaşanmayacaktır.
Önemli Duyuru: 24 Kasım 2025
Kasım 2025'ten itibaren üretilen Cudy AX3000 serisi yönlendiriciler (TR3000, seri numarası 2543 veya daha sonrasıyla başlayanlar. Seri numarasındaki 2543, 2025 yılının 43. haftasını ifade eder) yeni F50L1G41LC Flash belleği kullanmaktadır. OpenWrt ara belleniminin veya OpenWrt belleniminin eski sürümlerine yükseltme, cihazın başlatılmasını engelleyecektir. Bu nedenle, bu ürünler için kısıtlamalar eklemek üzere yeni bellenim güncellemeleri yayınlayacağız. Cihazın yeni Flash belleği kullandığı tespit edilirse, 2.3.X veya daha önceki eski bellenim sürümlerine yükseltme yapılamayacaktır. Ayrıca, eski Flash bellekli cihazlar için daha önce sağlanan OpenWrt ara bellenimi uyumlu olmayacaktır.
Etkilenen modeller şunlardır: AP3000 Outdoor 1.0, AP3000 Wall 1.0, M3000 1.0/2.0, TR3000 1.0, WR3000E 1.0, WR3000H 1.0, WR3000S 1.0 ve WR3000P 1.0.
Cudy, Google Drive'a güncellenen yeni OpenWrt ara yazılımlarını yayınladı. Lütfen yeni ara yazılıma geçin.
OpenWrt bellenimiyle ilgili olarak, yeni Flash ile uyumlu bir OpenWrt belleniminin resmi OpenWrt forumunda yayınlanmasını hala bekliyoruz. Yayınlandığında lütfen yeni OpenWrt bellenimini kullanın.
Seri numarası 2543'ten küçükse, eski flaş belleği kullanır. Böyle bir sorun yoktur.
Uyarılar
Bu web sayfası, OpenWrt sistemini destekleyen cihazların yazılımlarını listelemektedir. Yazılımı indirmeden ve kurmadan önce, OpenWrt Projesinin gömülü cihazları hedefleyen bir Linux işletim sistemi olduğunu lütfen unutmayın. OpenWrt, tek bir statik bellenim oluşturmaya çalışmak yerine, paket yönetimiyle birlikte tamamen yazılabilir bir dosya sistemi sağlar. Bu, satıcı tarafından sağlanan uygulama seçimi ve yapılandırmasından sizi kurtarır ve herhangi bir uygulamaya uygun hale getirmek için paketler kullanarak cihazı özelleştirmenize olanak tanır. Geliştiriciler için OpenWrt, etrafında eksiksiz bir bellenim oluşturmak zorunda kalmadan bir uygulama oluşturmak için bir çerçevedir; kullanıcılar için ise bu, cihazı hiç hayal edilmemiş şekillerde kullanabilme yeteneği anlamına gelir.
Tanım
- Bu dosya yalnızca yönlendiriciniz Cudy web arayüzü altında çalışıyorsa kullanılabilir.
- Eğer yönlendirici OpenWRT arayüzü altında zaten çalışıyorsa, kullanıcının öncelikle yönlendiriciyi Cudy resmi yazılımına geri yüklemesi ve ardından bu yazılımla yönlendiriciyi yükseltmesi gerekir.
- Yönlendiriciyi Cudy resmi yazılımına nasıl geri yükleyebilirim? Lütfen indirdiğiniz dosyadaki readme dosyasını okuyun.
Garanti:
Cudy işbu belgeyle beyan eder
- Biz, Cudy olarak, Shenzhen Cudy Technology Co., Ltd. tarafından piyasaya sürülmemiş hiçbir yazılım için garanti vermiyoruz.
- Shenzhen Cudy Technology Co., Ltd. tarafından piyasaya sürülmemiş herhangi bir yazılımın yüklendiği ürünler için hiçbir garanti vermiyoruz.
- OpenWrt yazılımını kullanmanız gerekiyorsa, Cudy'nin resmi web sitesinden indirmenizi öneririz.
İmza kontrolünü kaldırmak için OpenWrt Firmware'ini indirin:Sürmek
OpenWrt Firmware Finder (Cudy Tarafından Yayınlanmadı):OpenWrt Firmware Seçici
1309 yorum
@Dear Bourn,
There is no OpenWrt firmware for AP1300 V1.0 currently. The OpenWrt firmware is not developed by Cudy but by the developers. We need the OpenWrt forum official support the router at first, then we can release a middle firmware for you, then you can use and upgrade to the OpenWrt firmware.
“Hello,
I own a Cudy AP1300 1.0 access point and would like to install OpenWrt.
https://www.cudy.com/products/ap1300-1-0
Could you please provide an OpenWrt firmware image without signature verification that can be installed via the stock web interface?"
Hi Cudy Support Team , I’ve tried what you suggested – flashing older official firmware, but no luck , my Cudy WR3000 v1 is still bootlooping. Is there any firmware or recovery steps that I might perform in order to recover my router so I be able to boot into GUI ?
One more note : after flashing your firmware from Google drive or OpenWRT firmware, I’m able to enter to OpenWRT failsafe mode and access router via LAN using SSH , but from there I wasn’t able to perform system restoration steps from OpenWRT guides( I just don’t know how to do it propertly) . Thanks is advice for your support.
“@Dear Michael,
You can try to recover the old firmware version. Such as the 2.0.0, 2.2.6. Please connect the LAN port when recovering the firmware.
“Hi Cudy Support Team , I have purchased cudy wr3000 v1 router at the end of y 2023 ,I’ve successpully installed openwrt on my router using intermideate Cudy firmware, that was about 2 years ago. Then year after at 2024 ,I decided to go back to Cudy’s official firmware using OpenWrt system update and latest official firware at that moment .But something went wrong ( as I understood, there was some internal flash incompatibility with newer firmwares and older routers caused by internal flash)
As for today 2026 , my WR3000 v1 router is bootlooping endlessly but I’m able to upload firmware using tftp64.
What I’ve tried:
– Uploading latest official firmware v WR3000-R31-2.4.19 via tftp64 (using WAN port and LAN1 port )
– Uploading itermideate firmware from google drive , using tftp64 via LAN1 port and WAN port ,
– Uploading latest openwrt firmware v24.10.5 using tftp64 via WAN and LAN1 port .
- Uploading openwrt kernel only firmware based on v24.10.5 via WAN and LAN1 port .
Only when uploade official Cudy firmware ,the device rebooted itself autoamtically afer 3-4 minutes. In all cases the device is bootloping after manual or automatic restart.
Do you have any suggestions ? Maybe some firwmare to restore the device ?”"
WR3000P2550 . Can’t change to intermdiate cudy_wr3000p-v1-sysupgrade_20251119.bin: “File is invalid. Please retry.”
is it possible to get openwrt for WR3000P with new serial number?
Hello,
I own a Cudy AP1300 1.0 access point and would like to install OpenWrt.
https://www.cudy.com/products/ap1300-1-0
Could you please provide an OpenWrt firmware image without signature verification that can be installed via the stock web interface?
@Dear Roman,
Please try to update the intermediate firmware again. Note: The IP address of the router will change to 192.168.1.1 after update. You must check if your computer gets the correct IP address from the router and login the web page with 192.168.1.1.
“Hello! I do have Cudy WR3000E v1.0 with S/N: WR3000E254702030 having problem installing Intermediate firmware to install OpenWrt after that. I’ve tried to install cudy_wr3000e-v1-sysupgrade_20251119.bin from https://drive.google.com/drive/folders/1BKVarlwlNxf7uJUtRhuMGUqeCa5KpMnj but the router won’t start after installing it. Only 1 LED of Power is working so i have to start the recovery process with Tftpd64.”