Güncelleme: 24 Aralık 2025 İyi haber!
OpenWrt forumu, yeni Flash F50L1G41LC'yi destekleyen ve OpenWrt ürün yazılımını 24.10.5 sürümüne güncelleyen yamayı birleştirdi. Bu nedenle, gelecekte Cudy ile ilgili modelleri güncellemek için OpenWrt ürün yazılımının 24.10.5 veya daha yeni bir sürümünü indirirseniz, herhangi bir sorun yaşanmayacaktır.
Önemli Duyuru: 24 Kasım 2025
Kasım 2025'ten itibaren üretilen Cudy AX3000 serisi yönlendiriciler (TR3000, seri numarası 2543 veya daha sonrasıyla başlayanlar. Seri numarasındaki 2543, 2025 yılının 43. haftasını ifade eder) yeni F50L1G41LC Flash belleği kullanmaktadır. OpenWrt ara belleniminin veya OpenWrt belleniminin eski sürümlerine yükseltme, cihazın başlatılmasını engelleyecektir. Bu nedenle, bu ürünler için kısıtlamalar eklemek üzere yeni bellenim güncellemeleri yayınlayacağız. Cihazın yeni Flash belleği kullandığı tespit edilirse, 2.3.X veya daha önceki eski bellenim sürümlerine yükseltme yapılamayacaktır. Ayrıca, eski Flash bellekli cihazlar için daha önce sağlanan OpenWrt ara bellenimi uyumlu olmayacaktır.
Etkilenen modeller şunlardır: AP3000 Outdoor 1.0, AP3000 Wall 1.0, M3000 1.0/2.0, TR3000 1.0, WR3000E 1.0, WR3000H 1.0, WR3000S 1.0 ve WR3000P 1.0.
Cudy, Google Drive'a güncellenen yeni OpenWrt ara yazılımlarını yayınladı. Lütfen yeni ara yazılıma geçin.
OpenWrt bellenimiyle ilgili olarak, yeni Flash ile uyumlu bir OpenWrt belleniminin resmi OpenWrt forumunda yayınlanmasını hala bekliyoruz. Yayınlandığında lütfen yeni OpenWrt bellenimini kullanın.
Seri numarası 2543'ten küçükse, eski flaş belleği kullanır. Böyle bir sorun yoktur.
Uyarılar
Bu web sayfası, OpenWrt sistemini destekleyen cihazların yazılımlarını listelemektedir. Yazılımı indirmeden ve kurmadan önce, OpenWrt Projesinin gömülü cihazları hedefleyen bir Linux işletim sistemi olduğunu lütfen unutmayın. OpenWrt, tek bir statik bellenim oluşturmaya çalışmak yerine, paket yönetimiyle birlikte tamamen yazılabilir bir dosya sistemi sağlar. Bu, satıcı tarafından sağlanan uygulama seçimi ve yapılandırmasından sizi kurtarır ve herhangi bir uygulamaya uygun hale getirmek için paketler kullanarak cihazı özelleştirmenize olanak tanır. Geliştiriciler için OpenWrt, etrafında eksiksiz bir bellenim oluşturmak zorunda kalmadan bir uygulama oluşturmak için bir çerçevedir; kullanıcılar için ise bu, cihazı hiç hayal edilmemiş şekillerde kullanabilme yeteneği anlamına gelir.
Tanım
- Bu dosya yalnızca yönlendiriciniz Cudy web arayüzü altında çalışıyorsa kullanılabilir.
- Eğer yönlendirici OpenWRT arayüzü altında zaten çalışıyorsa, kullanıcının öncelikle yönlendiriciyi Cudy resmi yazılımına geri yüklemesi ve ardından bu yazılımla yönlendiriciyi yükseltmesi gerekir.
- Yönlendiriciyi Cudy resmi yazılımına nasıl geri yükleyebilirim? Lütfen indirdiğiniz dosyadaki readme dosyasını okuyun.
Garanti:
Cudy işbu belgeyle beyan eder
- Biz, Cudy olarak, Shenzhen Cudy Technology Co., Ltd. tarafından piyasaya sürülmemiş hiçbir yazılım için garanti vermiyoruz.
- Shenzhen Cudy Technology Co., Ltd. tarafından piyasaya sürülmemiş herhangi bir yazılımın yüklendiği ürünler için hiçbir garanti vermiyoruz.
- OpenWrt yazılımını kullanmanız gerekiyorsa, Cudy'nin resmi web sitesinden indirmenizi öneririz.
İmza kontrolünü kaldırmak için OpenWrt Firmware'ini indirin:Sürmek
OpenWrt Firmware Finder (Cudy Tarafından Yayınlanmadı):OpenWrt Firmware Seçici
1309 yorum
@Dear wahlfisch,
Still need some time. Please wait patiently.
“Dear Support, Any news regarding AP1300E Wall Firmware mid firmware without signing?”
Dear Support !
Purchased AP3000_P v1 access point.
Tried to flash according to the instructions from your website in openwrt through the transition firmware taken from you on google drive.
After flashing to the transition firmware, the access point lost access via lan cable ( wifi is not enabled ).
On the openwrt website found information:
As of jan. 2026, some devices are shipped with an alternate chip for single LAN port.
Now the access point is not available via lan or wi-fi.
What should I do to get the access point back online?I also can’t download the factory firmware via Recovery using the instructions on your website because the lan port is still not available.
Dear Support, Any news regarding AP1300E Wall Firmware mid firmware without signing?
“@Dear wahlfisch,
OK, I will do it.
““Sorry, there is no intermediate firmware for AP1300E Wall AP. The OpenWrt firmware is not developed by Cudy but by the developers. We need the OpenWrt forum official support the router at first, then we can release a middle firmware for you, then you can use and upgrade to the OpenWrt firmware”
Dear Support,
It would be easier, if you would provide some kind of intermediate firmware first (with fw signing disabled and so on)""
@Dear Marcel,
We don’t have plan to add the VLAN + SSID support on the WR3000H and WR11000.
In addition, The OpenWrt firmware is not developed by Cudy but by the developers. We need the OpenWrt forum official support the router at first, then we can release a middle firmware for you, then you can use and upgrade to the OpenWrt firmware.
“These are great devices. I’ve bought quite a few of them — around 10 units of the WR3000H and recently also a few BE11000.
What’s a bit unfortunate is that the WR3000H with OpenWrt supports VLANs for different SSIDs. The BE11000, however, understandably doesn’t have OpenWrt yet. On the other hand, the stock firmware on the BE11000 already supports assigning SSIDs to VLANs.
So the situation is a bit paradoxical: the BE11000 doesn’t have OpenWrt, while the WR3000H on stock firmware cannot assign SSIDs to VLANs (which OpenWrt can do). Because of this, users are forced to break the mesh network if they want to use VLANs properly.
It’s a bit disappointing because these are really good devices. The hardware clearly supports VLAN + SSID functionality, but unfortunately the stock firmware implementation on the WR3000H does not.
Is there any chance that VLAN + SSID support will be added to the firmware? Or do you perhaps plan to support OpenWrt on the BE11000 in the future?
I’d just like to know whether it makes sense to wait, or if I should simply move away from Cudy devices."
These are great devices. I’ve bought quite a few of them — around 10 units of the WR3000H and recently also a few BE11000.
What’s a bit unfortunate is that the WR3000H with OpenWrt supports VLANs for different SSIDs. The BE11000, however, understandably doesn’t have OpenWrt yet. On the other hand, the stock firmware on the BE11000 already supports assigning SSIDs to VLANs.
So the situation is a bit paradoxical: the BE11000 doesn’t have OpenWrt, while the WR3000H on stock firmware cannot assign SSIDs to VLANs (which OpenWrt can do). Because of this, users are forced to break the mesh network if they want to use VLANs properly.
It’s a bit disappointing because these are really good devices. The hardware clearly supports VLAN + SSID functionality, but unfortunately the stock firmware implementation on the WR3000H does not.
Is there any chance that VLAN + SSID support will be added to the firmware? Or do you perhaps plan to support OpenWrt on the BE11000 in the future?
I’d just like to know whether it makes sense to wait, or if I should simply move away from Cudy devices.