Подготовка:
1. Установите антенны и расположите их вверх.
2. Вставьте SIM-карту в слот до щелчка.
3. Подключите адаптер питания к маршрутизатору и включите его.
Шаг 1:
Откройте веб-браузер и перейдите по адресу http://cudy.net или http://192.168.10.1. Введите пароль администратора для входа.
Примечание. Паролем администратора по умолчанию является «admin», если версия прошивки 1.Х.Х. Мы удалили пароль администратора по умолчанию, начиная с версии прошивки 2.X.X. При первом входе в систему необходимо установить пароль администратора.
Подробную информацию см. в Как войти в веб-интерфейс Cudy Router?
Шаг 2. Откроется окно быстрой настройки. , выберите свой «часовой пояс».
Шаг 3. Настройте параметры APN. В большинстве случаев нам достаточно оставить для профиля APN значение «Авто». Затем нажмите «Далее». Маршрутизатор автоматически выберет параметры APN. (Рекомендуется)
Если вы хотите настроить параметры APN. Вы можете выбрать профиль APN как «Вручную» и ввести правильные параметры APN.
Примечание. Если вы не уверены в APN параметров, обратитесь к своему интернет-провайдеру.
Шаг 4. Измените имя и пароль беспроводной сети или оставьте их по умолчанию.
Шаг 5: Нажмите "Сохранить и применить", чтобы завершить настройку.
Шаг 6: Когда статус подключен, вы можете пользоваться Интернетом.
Комментариев: 52
@Dear Sakai,
You can set the metric of the WAN connection. The small the metric, the higher priority the WAN connection.
For the new firmware, it is under development currently. We will release a new firmware in the near future.
“R700 V1.0
I bought this router recently and this has never received any firmware update since its release date. Can you guys work on its latest firmware? Currently, we are unable to put multiple IP ranges when making a rule set to route specific data through a specific WAN.
Also, the rule is not applying properly sometimes. In the policy tab, you can not give priority to a specific WAN. Please fix these."
R700 V1.0
I bought this router recently and this has never received any firmware update since its release date. Can you guys work on its latest firmware? Currently, we are unable to put multiple IP ranges when making a rule set to route specific data through a specific WAN.
Also, the rule is not applying properly sometimes. In the policy tab, you can not give priority to a specific WAN. Please fix these.
@Dear Tommy,
Generally, there is no need to set the router. Just connect the devices to the LAN ports of the router. Then it will work. You can try to reset the router to factory default by long pressing the reset button for about 3 seconds. You can release the reset button when the LED flashes. Then connect all the devices and check if the problem avoided?
In addition, please check if the CCTV camera is set to get the IP address via DHCP when connect to the router via wired cable? If not, please set it.
“Dear Cudy team. How should I configure your router lt500D to be able to connect two CCTV cameras via Ethernet cable? I was able to connect only one that supports wifi, second one can be connected only via cable. Your router does not see these devices in lan network.”
Dear Cudy team. How should I configure your router lt500D to be able to connect two CCTV cameras via Ethernet cable? I was able to connect only one that supports wifi, second one can be connected only via cable. Your router does not see these devices in lan network.
@Dear Amigos,
The AT command for checking EARFCN is AT+QENG=“servingcell” , You can also check it in the syslog. For example
AT+QENG=“servingcell” → AT+QENG=“servingcell” +QENG: “servingcell”,“NOCONN”,“LTE”,“FDD”,250,01,41720C,9,1802,3,5,5,454C,-89,-10,-59,14,35 OK
The “1802” is the EARFCN.
For cell ID, we don’t have plan to change the format.
“Hi! In first iam need to say thanks for very balanced products with Cudy brand. Anyway i have some question about Cudy LT400 Outdoor functions.
1 – in Status we have data about LTE connection as MCC MNC CID and PCID, but not EARFCN and not eNodeB ID. How i can get it? Modem have this data by cell.
2- Cell ID have hex format. possible convert it in dec format Base ID?
and very important
need AT commands LIST for internal modem.
Thanks!"