Прежде чем создавать Mesh-сеть
1. Убедитесь, что есть по крайней мере два устройства Cudy.
2. Убедитесь, что все имеющиеся устройства Cudy поддерживают технологию Mesh.
3. Убедитесь, что на всех устройствах установлена последняя версия прошивки.
4. Убедитесь, что все устройства находятся в одной комнате (на время настройки).
5. Восстановите заводские настройки на всех устройствах Cudy.
6. Настройте основное Mesh-устройство и установите на нём подключение к интернету.
Инструкция по созданию Mesh-сети
В данном примере используются модели M1800 и WR2100:
Шаг 1. Введите в адресной строке браузера http://cudy.net или http://192.168.10.1.
Шаг 2. Нажмите на знак плюса (+) в разделе «Состояние системы».
Шаг 3. Нажмите на кнопку WPS на корпусе устройства M1800, затем нажмите на кнопку WPS на корпусе устройства WR2100.
Индикатор на основном Mesh-модуле должен мигать белым. Индикатор на вспомогательном Mesh-модуле должен мигать красно-белым.
Шаг 4. Откроется окно Сканирование, затем окно Подключение.
Шаг 5. Дождитесь, когда индикатор на вспомогательном модуле будет непрерывно гореть синим, затем переместите WR2100 в нужное место.
Шаг 6. Mesh-сеть успешно создана!
Комментариев: 87
Subject: Mesh Configuration with LT500 and WR1300 Routers
Dear Support Team,
I understand that the LT500 can only function as a main Mesh router and cannot be used as a satellite node.
I currently have three routers:
LT500
WR1300
LT500
Two of the LT500 units have access to the internet via 4G.
Is it possible to set up a Mesh network where all three devices are working together?
For example:
LT500 (main) + WR1300 (satellite)
The second LT500 (also with 4G) + the same WR1300 (as a satellite again)
In other words, can the same WR1300 be linked as a Mesh satellite to two separate LT500 routers?
Thank you for your assistance.
@Tahseen,
We suggest 8 nodes.
“Hello, how many Cudy M3000 V2 AX3000 V2.0 https://www.cudy.com/products/m3000-2-0 can be used in a Mesh environment? Is there any threshold to signal strength (RSSI). Thanks, Tahseen”
@Andre van der weide,
Sorry for the inconvenience caused to you!
Please set the SSID of M3000 separately on 2.4GHz and 5GHz. Then connect to the 5GHz WiFi if the clients support 5GHz. The 2.4GHz is not as good as the 5GHz if the signal strength is weak.
“I have m3000 cudy mesh units i don’t know if version 1 ore 2.
5ghz working perfect but 2.4 mhz the network is sometimes found and connect but no internet connection. i have the latest firmware 2.3.8 on al 3 cudy’s
My wife get angry every time because no connection on phone and switching off wifi”
@Dear Fouad,
Yes, you can install mesh system with them via Wi-Fi or wired cable.
“I want to know if i buy 3x WR3000, if i can use them in MESH mode?”
Hello, how many Cudy M3000 V2 AX3000 V2.0 https://www.cudy.com/products/m3000-2-0 can be used in a Mesh environment? Is there any threshold to signal strength (RSSI). Thanks, Tahseen