Шаг 1. Введите в адресной строке браузера http://cudy.net или http://192.168.10.1.
Шаг 2. Перейдите в раздел Общие настройки 🡢 VPN и переведите переключатель Включить в подразделе VPN во включённое положение.
Чтобы включить (отключить) VPN для конкретных устройств, перейдите в раздел Состояние системы 🡢 Устройства и переведите переключатель VPN напротив нужного устройства в нужное положение.
Шаг 3. В выпадающем списке параметра Протокол выберите нужный протокол и настройте параметры согласно указаниям поставщика VPN-услуг.
PPTP
Введите адрес VPN-сервера (например, 113.92.73.163), а также имя пользователя и пароль, предоставленные поставщиком VPN-услуг.
L2TP
Введите адрес VPN-сервера (например, 113.92.73.163), а также имя пользователя, пароль и ключ PSK, предоставленные поставщиком VPN-услуг.
Если поставщик VPN-услуг также предоставляет IP-адрес для привязки учётной записи, активируйте параметр Использовать пользовательский IP-адрес туннеля.
OpenVPN
Нажмите на кнопку Обзор... и импортируйте файл настроек, полученный от поставщика VPN-услуг.
WireGuard
Нажмите на кнопку Обзор... и импортируйте файл настроек, полученный от поставщика VPN-услуг.
Поля подразделов Интерфейс и Одноранговый узел будут заполнены автоматически с помощью файла настроек (CONF) поставщика VPN-услуг.
ZeroTier
Введите нужные значения в поля Идентификатор сети ZeroTier и Шлюз.
Комментариев: 196
hello!
wr3000h vpn settings work incorrectly. when i setup openvpn or wireguard clients some settings don’t work. don’t work the most important setting – VPN Policy (Domain). Rule Allow listed only Domains doesn’t work.
maybe you have new firmware or some solution.
Thanks.
| HW: WR3000H V1.0 | FW: 2.2.7-20240906-085755 |
@V Singh,
Dear Customer,
Thank you for contacting Cudy support team.
Our technical support has sent you the solutions via email. Please check.
“Hi, I’m trying to utilise two Cudy LT700 routers for site to site VPN connection. Server and client both are running on 4G sims. Server has a DDNS setup which client is able to reach using TRACEROUTE and NSLOOKUP. But after importing a VPN config file (tried with both OpenVPN and WireGuard), client still shows not connected to the VPN. The setups use default values for both VPNs. Any thoughts please to get this working? How shall I use the server hostname to get this resolved? Shall I also need to add DDNS for client and add to the client list on server?”
Hi, I’m trying to utilise two Cudy LT700 routers for site to site VPN connection. Server and client both are running on 4G sims. Server has a DDNS setup which client is able to reach using TRACEROUTE and NSLOOKUP. But after importing a VPN config file (tried with both OpenVPN and WireGuard), client still shows not connected to the VPN. The setups use default values for both VPNs. Any thoughts please to get this working? How shall I use the server hostname to get this resolved? Shall I also need to add DDNS for client and add to the client list on server?
@Jorge,
Dear Customer,
Our technical support has sent you the solutions via email. Please check.
“Hello,
I would like to configure VPN access on an AX3000 connected to the internet with a SIM card as it is located in a remote location where there is no fiber access. Is this possible?
Could you tell me how to configure the VPN to access the network from outside?
Regards and thanks in advance.”
@Johan,
Dear Customer,
Our technical support has sent you the solutions via email. Please check.
“I have a Cudy R700 router setup with two wan Ports and linked tot two tp-link 4g routers
when im onsite and pluged in i can access my routers on the 192.168.1.1/24 range
but when i connect to the vpn i setup with openvpn server and i connect i cant access none of my wan ports or log in to my tp-link routers through the vpn i did switch on management but still no luck please i need this working other wise i have to go to reyee cloud router”