1. Baixe e descompacte o arquivo deaqui.
2. Baixe o firmware mais recente dosite oficiale renomeie-o para 'recovery.bin'.Nota: Você deve colocá-lo no mesmo arquivo das ferramentas do Tftpd.
3. Desligue o roteador. Desconecte o adaptador de energia ou pressione o botão POWER.
4. Conecte seu computador à porta LAN do roteador com um cabo Ethernet.
5. Configure manualmente o endereço IP do seu computador como '192.168.1.88'.
6. Corra 'tftp32.exe'.
7. Corra 'netsh advfirewall desativa o estado de todos os perfis' na linha de comando para desabilitar o firewall do Windows, caso contrário, o tftp será bloqueado. Ou você pode desabilitar o firewall no Painel de Controle do seu computador. Como mostrado abaixo.
8. Pressione o botão 'Reiniciar' botão/orifício e segure-o. Antes de ligar o roteador e antes que o tftp comece a baixar o firmware, não solte o botão 'Reiniciar' botão/buraco.
9. Ligue o roteador.
10. Quando todas as luzes estiverem piscando rapidamente, ou quando o tftp começar a baixar o firmware, você pode soltar o 'Reiniciar' botão/buraco.
11. Quando a luz piscar lentamente, a atualização estará concluída.
12. Recupere o endereço IP do seu computador para um IP dinâmico.
13. Pronto.
142 comentários
@Ahmad,
Dear Customer,
Thank you for contacting Cudy support team.
Our technical support has contacted you via email. Please check.
“Hi, why I couldn’t download any files? got 404”
Hi, why I couldn’t download any files? got 404
@Alexander
Dear Customer,
Yes, you are right.
“OK, answer this myself (for TR3000 v1.0):
1. Find and download tftp32.exe
2. make directory “tftpboot”
3. put tftp32.exe AND the firmware (renamed to “recovery.bin”) into that directory
4. connect your PC to the LAN-port of the device
5. set your LAN IP to 192.168.1.88 like described here.
6. disable windows firewall (can do this with click and point in windows)
7. start tftp from the directory in step 2. and leave that window open
8. press reset-button on the device and then connect it to power/power on, keep pressed and wait, until it starts blinking/downloading the firmware to the device (in my case this was done after 3 seconds)
9. Enable firewall again, enable dynamic config (DHCP) on your lan port again, re-connect your lan and start to configure your Cudy device”
OK, answer this myself (for TR3000 v1.0):
1. Find and download tftp32.exe
2. make directory “tftpboot”
3. put tftp32.exe AND the firmware (renamed to “recovery.bin”) into that directory
4. connect your PC to the LAN-port of the device
5. set your LAN IP to 192.168.1.88 like described here.
6. disable windows firewall (can do this with click and point in windows)
7. start tftp from the directory in step 2. and leave that window open
8. press reset-button on the device and then connect it to power/power on, keep pressed and wait, until it starts blinking/downloading the firmware to the device (in my case this was done after 3 seconds)
9. Enable firewall again, enable dynamic config (DHCP) on your lan port again, re-connect your lan and start to configure your Cudy device
Sadly this does not work with my TR3000:
1. The download link (for tftp32?) is broken/does not work.
2. It doesn’t say where to put the sysupgrade firmware after download.
3. Does the sysupgrade firmware have to be renamed (to “recovery.bin”)?
Actually the stock vendor firmware for me is better/easier than open-wrt. So it should be possible to reflash to stock fw.