1. Baixe e descompacte o arquivo deaqui.
2. Baixe o firmware mais recente dosite oficiale renomeie-o para 'recovery.bin'.Nota: Você deve colocá-lo no mesmo arquivo das ferramentas do Tftpd.
3. Desligue o roteador. Desconecte o adaptador de energia ou pressione o botão POWER.
4. Conecte seu computador à porta LAN do roteador com um cabo Ethernet.
5. Configure manualmente o endereço IP do seu computador como '192.168.1.88'.
6. Corra 'tftp32.exe'.
7. Corra 'netsh advfirewall desativa o estado de todos os perfis' na linha de comando para desabilitar o firewall do Windows, caso contrário, o tftp será bloqueado. Ou você pode desabilitar o firewall no Painel de Controle do seu computador. Como mostrado abaixo.
8. Pressione o botão 'Reiniciar' botão/orifício e segure-o. Antes de ligar o roteador e antes que o tftp comece a baixar o firmware, não solte o botão 'Reiniciar' botão/buraco.
9. Ligue o roteador.
10. Quando todas as luzes estiverem piscando rapidamente, ou quando o tftp começar a baixar o firmware, você pode soltar o 'Reiniciar' botão/buraco.
11. Quando a luz piscar lentamente, a atualização estará concluída.
12. Recupere o endereço IP do seu computador para um IP dinâmico.
13. Pronto.
142 comentários
@Уважаемый Павел,
Какая прошивка у вашего Cudy TR30 (TR3000)? Это последняя версия прошивки 2.4.7? Если нет, пожалуйста, сначала обновите прошивку. Затем проверьте еще раз.
“Здравствуйте! При подключении к Cudy TR30 (TR3000) LTE модема, нет соединения. В настройках Cudy USB соединение неактивно. Что можно сделать?”
@Dear Alan,
So, why do you think it is the 256MB version. The 256MB version is only available for sell in China. The words on the label are in Chinese language, please have a check.
“Regarding the previous issue (failure to recover TR3000-256MB), I was finally able to revive it from being bricked using TTL. My router itself has no any hardware faults. I discovered that the NAND chip’s memory size differs from what is indicated on the box or label. This mismatch led to flashing the wrong version, causing it to become bricked and continuously reboot.
The chip inside is an ESMT F50L1G41LB, which can be broken down as follows:
F – Manufacturer: ESMT 50 – Product Collection L – Low Voltage (DDR3L) 1G – Density: 1Gb (Single Capacity) 41 – Organizational Structure: x16 (16-bit wide) LB – Packages and Versions
The capacity of a single unit is calculated as follows:
1Gb ÷ 8 bits/byte = 128MB
I hope you all don’t have to deal with the same issue I experienced. I’ve reached out to sales@cudy.com but haven’t received a response yet."
Здравствуйте! При подключении к Cudy TR30 (TR3000) LTE модема, нет соединения. В настройках Cudy USB соединение неактивно. Что можно сделать?
Regarding the previous issue (failure to recover TR3000-256MB), I was finally able to revive it from being bricked using TTL. My router itself has no any hardware faults. I discovered that the NAND chip’s memory size differs from what is indicated on the box or label. This mismatch led to flashing the wrong version, causing it to become bricked and continuously reboot.
The chip inside is an ESMT F50L1G41LB, which can be broken down as follows:
F – Manufacturer: ESMT 50 – Product Collection L – Low Voltage (DDR3L) 1G – Density: 1Gb (Single Capacity) 41 – Organizational Structure: x16 (16-bit wide) LB – Packages and VersionsThe capacity of a single unit is calculated as follows:
1Gb ÷ 8 bits/byte = 128MB
I hope you all don’t have to deal with the same issue I experienced. I’ve reached out to sales@cudy.com but haven’t received a response yet.
@Уважаемый Павел,
Пожалуйста, следуйте этой инструкции шаг за шагом. Если это не поможет, попробуйте выполнить эту операцию на другом компьютере.
“Здравствуйте! После прошивки роутера Cudy TR30 (TR3000) на OpenWRT решил прошить на заводскую прошивку и видимо бэкап не прошился. Теперь роутер не загружается и не заходит в web панель управления. Как можно это исправить?”