O sistema Mesh Cudy Whole Home foi desenvolvido para eliminar zonas mortas e fornecer Wi-Fi ininterrupto em toda a sua casa. Este artigo orientará você na construção de um sistema Mesh passo a passo.
Preparação:
1. Certifique-se de possuir pelo menos 2 produtos Cudy.
2. Todos os produtos Cudy são compatíveis com a tecnologia mesh: Home Mesh-Site oficial da Cudy
3. O firmware está atualizado:Centro de downloads
4. Leve-os para a mesma sala durante a configuração.
5. Redefina todos os seus produtos Cudy para as configurações de fábrica. (Com o aparelho ligado, pressione e segure o botão RESET com um alfinete por 6 segundos e depois solte.)
6. Configure seu roteador principal e conecte-o à Internet.
Aqui tomamos M1800 e WR2100 como exemplos:
Passo 1: Abra um navegador da web e vá parahttp://cudy.netouhttp://192.168.10.1.
Para mais detalhes, consulteComo fazer login na interface web do Cudy Router?
Passo 2: Na página Status do Sistema, clique no botão "+".
Etapa 3: Pressione o botão WPS no M1800 e depois pressione o botão WPS no WR2100.
Unidade de malha principal: Flash branco
Unidade de malha adicional: pisca em branco e vermelho alternadamente
Passo 4:Irá para "Digitalização", então "Conectando".
Passo 5: Aguarde até que o LED do sistema do roteador complementar fique azul sólido e, em seguida, reposicione o WR2100.
Passo 6: Sucesso e aproveite a rede mesh.
Observação:
1. O roteador 4/5G só pode ser configurado como uma unidade mesh principal. Por exemplo:
2. Você não conseguirá acessar a interface web do roteador mesh adicional. Se desejar alterar as configurações, clique em "Status do sistema"->"Malha".
71 comentários
@Dear Kamil,
I think the camera is connected to the 2.4GHz WiFi of the router. You can try to change the mode of 2.4GHz to 802.11b+g+n mode. Then check if the camera is able to connect to it?
“I built a mesh network using four WR3600E routers, and the internet works great. However, this network was meant for cctv monitoring, and that’s where the problem appeared: when the routers are in mesh mode, the cameras won’t log into the network, no matter which WPA level we choose. Only after disabling encryption and the password do the cameras connect to Wi-Fi. The cameras are XMeye. Is there any solution? When connected to lan port everything works. I’ll add that when the router is not in mesh mode, the same camera connects to it normally with wifi. Regards.”
I built a mesh network using four WR3600E routers, and the internet works great. However, this network was meant for cctv monitoring, and that’s where the problem appeared: when the routers are in mesh mode, the cameras won’t log into the network, no matter which WPA level we choose. Only after disabling encryption and the password do the cameras connect to Wi-Fi. The cameras are XMeye. Is there any solution? When connected to lan port everything works. I’ll add that when the router is not in mesh mode, the same camera connects to it normally with wifi. Regards.
@Dear Paweł,
Yes, you can. You can choose on of the M3000 to be the main mesh device. Then set it to working on the Mesh Access Point mode. Connect it to the network. Then reset all other Cudy devices to factory default. For the second M3000, please connect to the WAN port to the network. For the APs, please connect to the network directly. The Mesh system will be install automatically.
“Hi,
I have no cudy router as my main router, I’m going to disable wifi on that router and cerate mesh system viavwired backhaul. can I connect via eth 2 cudy m3000 and 2 ap3000 and cerate wired mesh between them with having fast roaming without creating subnet.”
Hi,
I have no cudy router as my main router, I’m going to disable wifi on that router and cerate mesh system viavwired backhaul. can I connect via eth 2 cudy m3000 and 2 ap3000 and cerate wired mesh between them with having fast roaming without creating subnet.
@Dear Kamil,
Yes, you can. Cudy mesh system supports Wired Backhaul. You can connect the WAN port of the satellite to the main mesh. It will work.
“Hi,
I have four wr3600e routers. One set as main router, and three as sattelites in wifi mesh mode. Can I connect one of them also with ethernet cable, to main router, to have better connection. This one is outside the building, and has low signal. BR Kamil”