Ubrīdinājumi
Šajā tīmekļa vietnē ir uzskaitīta ierīču programmatūra, kas atbalsta OpenWrt sistēmu, pirms lejupielādējiet un instalējiet programmatūru, lūdzu, ņemiet vērā, ka OpenWrt projekts ir Linux operētājsistēma, kas paredzēta iegultajām ierīcēm. Tā vietā, lai mēģinātu izveidot vienotu, statisku programmaparatūru, OpenWrt nodrošina pilnībā rakstāmu failu sistēmu ar pakešu pārvaldību. Tas atbrīvo jūs no ražotāja nodrošinātās lietojumprogrammu atlases un konfigurācijas un ļauj jums pielāgot ierīci, izmantojot paketes, lai tā atbilstu jebkurai lietojumprogrammai. Izstrādātājiem OpenWrt ir ietvars, kas ļauj izveidot lietojumprogrammu bez nepieciešamības ap to veidot pilnu programmaparatūru; lietotājiem tas nozīmē iespēju pilnībā pielāgot ierīci, lai to izmantotu tā, kā nekad nav iedomājušies.
Apraksts
- Šo failu var izmantot tikai tad, ja maršrutētājs darbojas ar Cudy tīmekļa lietotāja saskarni .
- Ja maršrutētājs jau darbojas ar OpenWRT UI, lietotājam vispirms jāatjauno to uz Cudy oficiālo firmware. Un pēc tam atjaunināt maršrutētāju ar šo programmaparatūru. .
- Kā atjaunot maršrutētāju uz Cudy oficiālo programmaparatūru? Lūdzu, izlasiet lejupielādētajā failā esošo readme. .
Garantija:
Cudy ar šo paziņo
- Mēs, Cudy, neuzņemamies garantiju attiecībā uz programmatūru, ko nav izlaidusi Shenzhen Cudy Technology Co., Ltd. .
- Mēs neuzņemamies nekādas garantijas produktiem, kuros ir instalēta jebkāda programmatūra, ko nav izlaidusi Shenzhen Cudy Technology Co., Ltd. .
- Ja jums ir nepieciešams izmantot openwrt programmatūru, iesakām to lejupielādēt no Cudy oficiālās vietnes. .
Saņemiet OpenWrt programmaparatūru, lai noņemtu paraksta pārbaudi: Drive
OpenWrt firmware meklētājs (nav izlaists Cudy): OpenWrt Firmware Selector
1019 comments
@Dear Michael,
Regarding the tftpd recovering firmware method. You can refer to this article.
https://www.cudy.com/blogs/faq/how-to-recovery-the-cudy-router-from-openwrt-firmware-to-cudy-official-firmware?pos=1&_sid=b98054b19&ss=r
You can download the firmware for you router via this link.
https://www.cudy.com/pages/download-center/wr3000-1-0
“Hello Cudy Support Team ,
Maybe you have some intermediate , temporary firmware ,that I can flash to my WR3000 v1 using tftp64 so it will restore it’s state to defaults ? with memory erasing and rebuilidng the filesystem ? Thaks in advance.”
Hello Cudy Support Team ,
Maybe you have some intermediate , temporary firmware ,that I can flash to my WR3000 v1 using tftp64 so it will restore it’s state to defaults ? with memory erasing and rebuilidng the filesystem ? Thaks in advance.
“@Dear Michael,
I see. I suggest you can try to do it by yourself. We don’t have such instructions.
“Hi Cudy Support Team , I’ve tried what you suggested – flashing older official firmware, but no luck , my Cudy WR3000 v1 is still bootlooping. Is there any firmware or recovery steps that I might perform in order to recover my router so I be able to boot into GUI ?
One more note : after flashing your firmware from Google drive or OpenWRT firmware, I’m able to enter to OpenWRT failsafe mode and access router via LAN using SSH , but from there I wasn’t able to perform system restoration steps from OpenWRT guides( I just don’t know how to do it propertly) . Thanks is advice for your support.
@Dear Support
I have already built a working OpenWrt firmware for AP1300 v1.0, based on the OpenWrt firmware for AP1300 Outdoor v1.0 (same SoC and hardware platform).
The firmware itself builds and boots, but I cannot flash it via TFTP or the web interface because the stock firmware requires a signed image.
To proceed without hardware modification (UART/SPI), I need an intermediate firmware that can be installed via the web interface and allows upgrading to a custom OpenWrt image (without signature verification).
Could you please provide such an intermediate firmware for AP1300 v1.0, or advise if there is an official way to bypass the signature check for development purposes?
Thank you.
“@Dear Bourn,
There is no OpenWrt firmware for AP1300 V1.0 currently. The OpenWrt firmware is not developed by Cudy but by the developers. We need the OpenWrt forum official support the router at first, then we can release a middle firmware for you, then you can use and upgrade to the OpenWrt firmware. "
@Dear Michael,
I see. I suggest you can try to do it by yourself. We don’t have such instructions.
“Hi Cudy Support Team , I’ve tried what you suggested – flashing older official firmware, but no luck , my Cudy WR3000 v1 is still bootlooping. Is there any firmware or recovery steps that I might perform in order to recover my router so I be able to boot into GUI ?
One more note : after flashing your firmware from Google drive or OpenWRT firmware, I’m able to enter to OpenWRT failsafe mode and access router via LAN using SSH , but from there I wasn’t able to perform system restoration steps from OpenWRT guides( I just don’t know how to do it propertly) . Thanks is advice for your support.”
@Dear A,
Our technical support has contacted you via email. Please check.
“WR3000P2550 . Can’t change to intermdiate cudy_wr3000p-v1-sysupgrade_20251119.bin: “File is invalid. Please retry.”
is it possible to get openwrt for WR3000P with new serial number?”