IP filtrs ļauj kontrolēt, kāda IP datplūsma tiks ielaista jūsu tīklā un no tā.
1.solis: Atveriet tīmekļa pārlūkprogrammu un dodieties uz http://cudy.net vai http://192.168.10.1.
Detalizētu informāciju skatīt Kā pieslēgties Cudy maršrutētāja tīmekļa saskarnei?"
Kāpiens 2: Noklikšķiniet uz Uzlabotie iestatījumi -> IP filtrs sadaļā Drošība.
3. solis: Cpārbaudiet iestatījumus IP filtra lapā.
- Lai bloķētu konkrētas IP adreses
1. Izvēlieties "Izslēgt visu, izņemot sarakstu".
2. Ievadiet IP adreses, kuras vēlaties bloķēt, un izvēlieties pareizo apakštīkla masku.
Piemērs: Visas ierīces nevar piekļūt Cudy oficiālajai vietnei.
3. Saglabāt & amp; Pielietot darbību.
1. Atlasiet "Izvēlēt tikai sarakstu"
2. Ievadiet IP adresi(-as), kurai(-ām) ir atļauts piekļūt.
Piemērs: Atļauts piekļūt tikai Cudy tīmekļa vietnei, citas tīmekļa vietnes nevarēs ielādēt.
3. Saglabāt & amp; Pielietot darbību.
Piezīme:Ja nevēlaties ierobežot internetu, no izlaižamā saraksta izvēlieties "Izslēgt" un saglabājiet iestatījumus, nevis tikai "Izdzēst" elementu.
8 comments
@Dear Hein,
For now, there is no limit on the ipv6 connection. I think you don’t need to worry about it. For IPv6 has additional security. And there is alo firewall on the terminals.
“Thanks, but you’ve still not answered my question. How do I prevent inbound connections to IPv6 enabled hosts? I don’t want them to be reachable from the Internet. Outbound connections should work (as it does), but I want inbound connections to be blocked. I.E. I’m able to ping my laptop from the Internet which is not desirable.”
Thanks, but you’ve still not answered my question. How do I prevent inbound connections to IPv6 enabled hosts? I don’t want them to be reachable from the Internet. Outbound connections should work (as it does), but I want inbound connections to be blocked. I.E. I’m able to ping my laptop from the Internet which is not desirable.
@Dear Hein,
You are right. If you enable this and you want to ping the WAN IP address of the router. It will response.
“Thanks,
I have a WR3600 running 2.3.12. SPI is on yes. I see there is an option “Respond to Ping” which is enabled which I assume means the router responds to ping and doesn’t relate to allowing ICMP through the router.”
Thanks,
I have a WR3600 running 2.3.12. SPI is on yes. I see there is an option “Respond to Ping” which is enabled which I assume means the router responds to ping and doesn’t relate to allowing ICMP through the router.
@Dear Hein,
What is the model and firmware of your router?
Do you disable the SPI Firewall of your router? Please check. We will test it.
“Hi,
I’ve enabled IPv6 on my router which works well. All inbound traffic is however allowed, which is undesirable in most cases since all my devices are directly reachable from the internet.
How do I enable IPv6 so I can communicate out without allowing inbound traffic?"