1. Lejupielādējiet un atinstalējiet failu no šeit.
2. Lejupielādējiet jaunāko programmaparatūru no oficiālās tīmekļa vietnes un pārdēvējiet to par 'recovery.bin'. Piezīme: Jums tas jāieliek tajā pašā Tftpd rīku failā.
3. Izslēdziet maršrutētāju. Atvienojiet strāvas adapteri vai nospiediet POWER pogu.
4. Savienojiet datoru ar maršrutētāja LAN portu, izmantojot Ethernet kabeli.
5. Manuāli konfigurējiet datora IP adresi "192.168.1.88".
6. Palaidiet 'tftp32.exe'.
7. Komandu rindā izpildiet 'netsh advfirewall set allprofiles state off', lai atspējotu Windows ugunsmūri, pretējā gadījumā tftp tiks bloķēts. Vai arī varat atspējot ugunsmūri datora vadības panelī. Kā parādīts tālāk.
8. Nospiediet "Atjaunināt" pogu/aizvērtni un turiet to. Pirms maršrutētājs tiek ieslēgts un pirms tftp sāk lejupielādēt programmaparatūru, neatlaidiet 'Reset' pogu/caurumu.
9. Ieslēdziet maršrutētāju.
10. Kad visas lampiņas ātri mirgo vai kad tftp sāk lejupielādēt programmaparatūru, varat atlaist "Reset" pogu/durvīti.
11. Kad lampiņa lēni mirgo, atjaunināšana ir pabeigta.
12. Lūdzu, atjaunojiet datora IP adresi, lai tā būtu dinamiskais IP.
13. Gatavs.
162 comments
@Ahmad,
Dear Customer,
Thank you for contacting Cudy support team.
Our technical support has contacted you via email. Please check.
“Hi, why I couldn’t download any files? got 404”
Hi, why I couldn’t download any files? got 404
@Alexander
Dear Customer,
Yes, you are right.
“OK, answer this myself (for TR3000 v1.0):
1. Find and download tftp32.exe
2. make directory “tftpboot”
3. put tftp32.exe AND the firmware (renamed to “recovery.bin”) into that directory
4. connect your PC to the LAN-port of the device
5. set your LAN IP to 192.168.1.88 like described here.
6. disable windows firewall (can do this with click and point in windows)
7. start tftp from the directory in step 2. and leave that window open
8. press reset-button on the device and then connect it to power/power on, keep pressed and wait, until it starts blinking/downloading the firmware to the device (in my case this was done after 3 seconds)
9. Enable firewall again, enable dynamic config (DHCP) on your lan port again, re-connect your lan and start to configure your Cudy device”
OK, answer this myself (for TR3000 v1.0):
1. Find and download tftp32.exe
2. make directory “tftpboot”
3. put tftp32.exe AND the firmware (renamed to “recovery.bin”) into that directory
4. connect your PC to the LAN-port of the device
5. set your LAN IP to 192.168.1.88 like described here.
6. disable windows firewall (can do this with click and point in windows)
7. start tftp from the directory in step 2. and leave that window open
8. press reset-button on the device and then connect it to power/power on, keep pressed and wait, until it starts blinking/downloading the firmware to the device (in my case this was done after 3 seconds)
9. Enable firewall again, enable dynamic config (DHCP) on your lan port again, re-connect your lan and start to configure your Cudy device
Sadly this does not work with my TR3000:
1. The download link (for tftp32?) is broken/does not work.
2. It doesn’t say where to put the sysupgrade firmware after download.
3. Does the sysupgrade firmware have to be renamed (to “recovery.bin”)?
Actually the stock vendor firmware for me is better/easier than open-wrt. So it should be possible to reflash to stock fw.