1. Lejupielādējiet un atinstalējiet failu no šeit.
2. Lejupielādējiet jaunāko programmaparatūru no oficiālās tīmekļa vietnes un pārdēvējiet to par 'recovery.bin'. Piezīme: Jums tas jāieliek tajā pašā Tftpd rīku failā.
3. Izslēdziet maršrutētāju. Atvienojiet strāvas adapteri vai nospiediet POWER pogu.
4. Savienojiet datoru ar maršrutētāja LAN portu, izmantojot Ethernet kabeli.
5. Manuāli konfigurējiet datora IP adresi "192.168.1.88".
6. Palaidiet 'tftp32.exe'.
7. Komandu rindā izpildiet 'netsh advfirewall set allprofiles state off', lai atspējotu Windows ugunsmūri, pretējā gadījumā tftp tiks bloķēts. Vai arī varat atspējot ugunsmūri datora vadības panelī. Kā parādīts tālāk.
8. Nospiediet "Atjaunināt" pogu/aizvērtni un turiet to. Pirms maršrutētājs tiek ieslēgts un pirms tftp sāk lejupielādēt programmaparatūru, neatlaidiet 'Reset' pogu/caurumu.
9. Ieslēdziet maršrutētāju.
10. Kad visas lampiņas ātri mirgo vai kad tftp sāk lejupielādēt programmaparatūru, varat atlaist "Reset" pogu/durvīti.
11. Kad lampiņa lēni mirgo, atjaunināšana ir pabeigta.
12. Lūdzu, atjaunojiet datora IP adresi, lai tā būtu dinamiskais IP.
13. Gatavs.
242 comments
I have a cudy n700, it does not seem to reset or enter recovery mode, this is the second one with the same issue can you assist with resolving this urgently
@Dear Otis,
I think there is something wrong with the router. The router can’t be recovered.
“Hello , i have a CudyWR3000 and i wish to put it in recovery mode so that i can tftp my way into openwrt , the issue is , i can not put in recovery mode , i have tried holding the reset button while its unplugged and then plug it back in and keep holding for 12 seconds , at times even longer and no matter what i do , i do not get a rapidly blinking light indicating recovery mode , all i get is a steady power led and the internet led slowly blinking ( mind you when its in that mode which is not recovery no other light is on , just those two) . I thought that perhaps its recovery mode and i am missing something , i went on with the process the same way i would with it being in recovery , no matter how many times i tried or changes i made tcpdump indicated no request coming from the router .”
@Estimado Javier:
De acuerdo. Creo que está relacionado con el canal de trabajo. Algunos canales no admiten 160 MHz.
“He tenido que volver a las versión del Firmware original, ya que en Openwrt al configurar la Wifi 5G en ancho de banda 160 mhz, desparece y no se puede conectar. He hecho muchas pruebas y es cambiarlo a 80 mhz y si funciona. Este problema con el firm de Cudy no pasa. Se queda configurado en 160mhz y todo normal.”
Hello , i have a CudyWR3000 and i wish to put it in recovery mode so that i can tftp my way into openwrt , the issue is , i can not put in recovery mode , i have tried holding the reset button while its unplugged and then plug it back in and keep holding for 12 seconds , at times even longer and no matter what i do , i do not get a rapidly blinking light indicating recovery mode , all i get is a steady power led and the internet led slowly blinking ( mind you when its in that mode which is not recovery no other light is on , just those two) . I thought that perhaps its recovery mode and i am missing something , i went on with the process the same way i would with it being in recovery , no matter how many times i tried or changes i made tcpdump indicated no request coming from the router .
He tenido que volver a las versión del Firmware original, ya que en Openwrt al configurar la Wifi 5G en ancho de banda 160 mhz, desparece y no se puede conectar. He hecho muchas pruebas y es cambiarlo a 80 mhz y si funciona. Este problema con el firm de Cudy no pasa. Se queda configurado en 160mhz y todo normal.