WISP režimas:
WISP režimu maršrutizatorius leidžia keliems naudotojams dalytis WISP interneto ryšiu. Tokiu būdu LAN prievado įrenginiai dalijasi tuo pačiu IP iš WISP per belaidį prievadą. Prijungus prie WISP, belaidis prievadas veikia kaip WAN prievadas.
Bendroji tinklo topologija:
1 žingsnis: Atverkite interneto naršyklę ir eikite į http://cudy.net arba http://192.168.10.1.
Išsamesnės informacijos rasite Kaip prisijungti prie "Cudy Router" žiniatinklio sąsajos?
2 žingsnis: Atsidarys greitosios sąrankos langas, pasirinkite "WISP", tada eikite "Next".
3. žingsnis: Pasirinkite savo "laiko zoną".
4 etapas: Pasirinkite norimą išplėsti kompiuterių tinklą. Spustelėkite "Prijungti".
Bendrieji nustatymai->WISP->Įjungti ir pasirinkite norimą išplėsti kompiuterių tinklą.
5 žingsnis: Įveskite priimančiojo tinklo belaidžio ryšio slaptažodį.
Pastaba: Užtikrinkite, kad įvestas belaidžio ryšio slaptažodis būtų teisingas, kitaip konfigūracija negali būti sėkminga.
6 etapas: Nustatykite belaidžio tinklo pavadinimą ir slaptažodį arba palikite juos numatytuosius.
7 etapas: Paspauskite "Save &; Apply", kad užbaigtumėte konfigūraciją.
8 etapas: Palaukite kelias sekundes, kol sistema bus perkrauta, kai vėl pasirodys prisijungimo puslapis, galėsite naudotis internetu.
114 comments
Hello Cudy Support. Could I also get please the beta version of Firmware supporting WISP work mode for the WR6500H router?
Thx
@Dear Peter Tomaščík,
Our technical support has sent you the firmware via email. Please check.
“I recently purchased the Cudy WR6500 as an upgrade to my older Cudy WR3000. My original plan was to use the new WR6500 as my main router and repurpose the WR3000 as a Mesh node to extend my network coverage.
However, I ran into a major issue: the WISP mode is missing in the WR6500 settings, whereas it works perfectly fine on the older WR3000.
Because the WR6500 lacks WISP support, I am currently forced to use it only as a Mesh extension instead of the main router, which completely degrades its performance and defeats the purpose of the upgrade.
Could the support team or anyone here provide me with a firmware version for the WR6500 that includes the WISP functionality?”
@Dear Lawson,
Please go to “General Settings” —"WISP " function page to set it up.
“I have the 4GvLTE N300 V3.0
I’ve got firmware 2.5.12 installed, but still no WISP
Could you send me the firmware that allows for Wisp please. I’m happy to test it if it’s Beta.”
@Dear John,
I think yes. WR1200 supports WISP function to connect the main Wi-Fi via wireless. But you must check if the signal strength starlink mini wifi router at the placement of WR1200 is powerful enough to connect to?
“Hi, can I use the wr1200 to feed wired internet into my lan from a starlink mini wifi router. I would like to not have a wire from the starlink into my existing lan which covers 4 floors of a concrete building. Is this compatible.
Thank you.”
I recently purchased the Cudy WR6500 as an upgrade to my older Cudy WR3000. My original plan was to use the new WR6500 as my main router and repurpose the WR3000 as a Mesh node to extend my network coverage.
However, I ran into a major issue: the WISP mode is missing in the WR6500 settings, whereas it works perfectly fine on the older WR3000.
Because the WR6500 lacks WISP support, I am currently forced to use it only as a Mesh extension instead of the main router, which completely degrades its performance and defeats the purpose of the upgrade.
Could the support team or anyone here provide me with a firmware version for the WR6500 that includes the WISP functionality?