Kas yra prieigos taško režimas?
Prieigos taško režimas - tai maršrutizatorius naudoja laidinį ryšį su pagrindiniu maršrutizatoriumi arba modemo maršrutizatoriumi, kad išplėstų namų tinklo belaidžio ryšio aprėptį.
Bendroji tinklo topologija:
1 žingsnis: Atverkite žiniatinklio naršyklę ir eikite į http://cudy.net arba http://192.168.10.1.
Išsamesnės informacijos rasite Kaip prisijungti prie "Cudy Router" žiniatinklio sąsajos?"
2 žingsnis: Atsidarys greitosios sąrankos langas, pasirinkite "Bezlaidis prieigos taškas", tada spustelėkite "Toliau".
Trečias žingsnis: Pasirinkite "Taikos zoną".
4 žingsnis: Patvirtinkite aparatinės įrangos ryšį.
5 žingsnis: Pakeiskite belaidžio tinklo pavadinimą ir slaptažodį.
Šeštas žingsnis: Spustelėkite "Save & amp; Apply", kad užbaigtumėte konfigūravimą.
7 žingsnis: Palaukite kelias sekundes, kol sistema bus perkrauta, kai vėl pasirodys prisijungimo puslapis, galėsite naudotis internetu.
Pastaba:
Nustačius Cudy maršrutizatorių į prieigos taško režimą, IP adresą priskirs pagrindinis maršrutizatorius, o numatytuoju IP adresu 192.168.10.1 prisijungti nepavyks. Jei norite vėl prisijungti prie Cudy maršrutizatoriaus, naršyklėje įveskite "http://cudy.net' arba ieškokite Cudy maršrutizatoriaus IP adreso pagrindinio (pagrindinio) maršrutizatoriaus klientų sąraše.
44 comments
@Werner
Dear Customer，
Thank you for contacting Cudy support team.
Please set the AP to static IP address, then reboot the main router, and check again.
“Hi, I have installed a Cudy 1300 Outdoor AP on a clients site, did the complete setup and as a wireless access point. I had set static ip address for the AP but werent internet connection through the AP, I then changed the AP’s ip setting to dhcp. On the status page it shows that the AP is connected to the internet via the lan cable but when I connect my laptop other device to the wifi its not getting internet access. Also cannot pin the gateway ip address from my laptop, but on the diagnostics page of the ap I can ping the gateway ip address. Can you please help with this, as I have a wireless camera connected to this AP but cannot access it from my lan.”
Hi, I have installed a Cudy 1300 Outdoor AP on a clients site, did the complete setup and as a wireless access point. I had set static ip address for the AP but werent internet connection through the AP, I then changed the AP’s ip setting to dhcp. On the status page it shows that the AP is connected to the internet via the lan cable but when I connect my laptop other device to the wifi its not getting internet access. Also cannot pin the gateway ip address from my laptop, but on the diagnostics page of the ap I can ping the gateway ip address. Can you please help with this, as I have a wireless camera connected to this AP but cannot access it from my lan.
@Steve,
Dear Customer,
Thank you for contacting Cudy support team. Please follow the steps:
1. Set the LAN IP address to the same subnet of the main router, it will be easy to login to the web page.
2. Set the WiFi SSID and password as you want.
3. Disable the DHCP server of the P5.
Then you can connect to the main router and use it as a AP.
“I have configured my P5 router, now I’d like to change it to Access Point. I can not see in the web interface any references at all to operation mode. How do I change the operation mode from wireless router to Access Point router?”
@Rafal,
Dear Customer,
Thank you for contacting Cudy support team.
Our technical support has sent you the solutions via email. Please check.
“Hi. I have an LT500 router upstairs with sim card and another downstairs connected in AP mode via ethernet cable to the 1st one due there is very little wifi signal coming between floors through the ceiling. It works well but results in 2 different wifi networks upstairs and downstairs. So when moving between rooms devices not always switch to the network with better signal. How to make it one network with same login and password on both floors? Is it possible to configure a mesh in this situation?”
I have configured my P5 router, now I’d like to change it to Access Point. I can not see in the web interface any references at all to operation mode. How do I change the operation mode from wireless router to Access Point router?