Hoiatused
See veebileht loetleb OpenWrt süsteemi toetavate seadmete tarkvara, enne tarkvara allalaadimist ja paigaldamist palume arvestada, et OpenWrt Project on Linuxi operatsioonisüsteem, mis on suunatud manussüsteemidele. Selle asemel, et püüda luua üksikut staatilist püsivara, pakub OpenWrt täielikult kirjutatavat failisüsteemi koos paketihaldusega. See vabastab teid müüja poolt pakutavate rakenduste valikust ja konfiguratsioonist ning võimaldab teil kohandada seadet pakettide abil mis tahes rakendusele sobivaks. Arendajate jaoks on OpenWrt raamistik, mille abil saab luua rakenduse, ilma et oleks vaja ehitada selle ümber täielikku püsivara; kasutajate jaoks tähendab see võimalust täielikuks kohandamiseks, et kasutada seadet viisil, mida nad pole kunagi ette kujutanud.
Kirjeldus
- Seda faili saab kasutada ainult siis, kui teie ruuter töötab Cudy veebi kasutajaliidese all.
- Kui ruuter juba töötab OpenWRT UI all, peaks kasutaja esmalt taastama selle Cudy ametliku firmware'ile. Ja seejärel uuendada ruuterit selle püsivara abil.
- Kuidas taastada ruuter Cudy ametlikule püsivara? Palun lugege alla laaditud faili readme.
Garantii:
Cudy deklareerib käesolevaga
- Me, Cudy, ei võta garantiid ühegi tarkvara eest, mida ei ole välja andnud Shenzhen Cudy Technology Co., Ltd. .
- Me ei võta garantiid toodete eest, millele on paigaldatud tarkvara, mida ei ole välja andnud Shenzhen Cudy Technology Co., Ltd. .
- Kui teil on vaja kasutada openwrt tarkvara, soovitame selle alla laadida Cudy ametlikust veebisaidist.
Laadige alla OpenWrt püsivara, et eemaldada allkirja kontroll: Ajama
OpenWrt Firmware Finder (ei ole Cudy poolt välja antud): OpenWrt Firmware Selector
1319 comments
Can you email me the signed intermediate OpenWRT firmware for WR3000S?
Thanks.
Is it possible to upload OpenWRT to the WR3000S router ? where can i find image and instructions.
@mike_ds,
Dear Customer,
Thank you for contacting Cudy support team.
The letter says that it will be impossible to return to the manufacturer’s firmware after switching to Openwrt. —No, you can return to the manufacturer’s firmware after switching to Openwrt via the TFTP method.
Tell me, is the Openwrt firmware that you sent stable? --This is not the OpenWrt firmware, this is just a intermediate firmware.
For the functions of the Openwrt firmware, you need to check it by yourself, we don’t know that. It is not developed by Cudy.
“Dear manufacturers. I want to install Openwrt on my Cudy AP3000 v1.0 access point (round with 2.5G port). You recently sent me the firmware by email – I am very grateful to you for your quick response. The letter says that it will be impossible to return to the manufacturer’s firmware after switching to Openwrt. What is the reason for this impossibility of returning to the factory? Tell me, is the Openwrt firmware that you sent stable? Will I regret this transition? Will the firmware have VLAN and Multi-SSID network management for wireless adapters, does PoE and the 2.5G port work in Openwrt? It is important for me to know the stability and performance of the Openwrt firmware before I transfer the AP3000 v.1.0 to a firmware from which it will then be impossible to return to factory settings. When the access point starts on the factory firmware, I see in the address line a reference to the luci interface, that is, similar to Openwrt, but modified by your development team. Therefore, I do not understand why it is impossible to switch back to the factory, in case of failure.”
Dear manufacturers. I want to install Openwrt on my Cudy AP3000 v1.0 access point (round with 2.5G port). You recently sent me the firmware by email – I am very grateful to you for your quick response. The letter says that it will be impossible to return to the manufacturer’s firmware after switching to Openwrt. What is the reason for this impossibility of returning to the factory? Tell me, is the Openwrt firmware that you sent stable? Will I regret this transition? Will the firmware have VLAN and Multi-SSID network management for wireless adapters, does PoE and the 2.5G port work in Openwrt? It is important for me to know the stability and performance of the Openwrt firmware before I transfer the AP3000 v.1.0 to a firmware from which it will then be impossible to return to factory settings. When the access point starts on the factory firmware, I see in the address line a reference to the luci interface, that is, similar to Openwrt, but modified by your development team. Therefore, I do not understand why it is impossible to switch back to the factory, in case of failure.
@Toni and Ian,
Dear Customer,
Thank you for contacting Cudy support team.
Our technical support has sent you via email. Please check.