Hoiatused
See veebileht loetleb OpenWrt süsteemi toetavate seadmete tarkvara, enne tarkvara allalaadimist ja paigaldamist palume arvestada, et OpenWrt Project on Linuxi operatsioonisüsteem, mis on suunatud manussüsteemidele. Selle asemel, et püüda luua üksikut staatilist püsivara, pakub OpenWrt täielikult kirjutatavat failisüsteemi koos paketihaldusega. See vabastab teid müüja poolt pakutavate rakenduste valikust ja konfiguratsioonist ning võimaldab teil kohandada seadet pakettide abil mis tahes rakendusele sobivaks. Arendajate jaoks on OpenWrt raamistik, mille abil saab luua rakenduse, ilma et oleks vaja ehitada selle ümber täielikku püsivara; kasutajate jaoks tähendab see võimalust täielikuks kohandamiseks, et kasutada seadet viisil, mida nad pole kunagi ette kujutanud.
Kirjeldus
- Seda faili saab kasutada ainult siis, kui teie ruuter töötab Cudy veebi kasutajaliidese all.
- Kui ruuter juba töötab OpenWRT UI all, peaks kasutaja esmalt taastama selle Cudy ametliku firmware'ile. Ja seejärel uuendada ruuterit selle püsivara abil.
- Kuidas taastada ruuter Cudy ametlikule püsivara? Palun lugege alla laaditud faili readme.
Garantii:
Cudy deklareerib käesolevaga
- Me, Cudy, ei võta garantiid ühegi tarkvara eest, mida ei ole välja andnud Shenzhen Cudy Technology Co., Ltd. .
- Me ei võta garantiid toodete eest, millele on paigaldatud tarkvara, mida ei ole välja andnud Shenzhen Cudy Technology Co., Ltd. .
- Kui teil on vaja kasutada openwrt tarkvara, soovitame selle alla laadida Cudy ametlikust veebisaidist.
Laadige alla OpenWrt püsivara, et eemaldada allkirja kontroll: Ajama
OpenWrt Firmware Finder (ei ole Cudy poolt välja antud): OpenWrt Firmware Selector
1319 comments
@Marek
Dear Marek,
The correct connection rate is 115200. Please have a try. You can try to recover the device according to the instruction on the website:
https://www.cudy.com/blogs/faq/how-to-recovery-the-cudy-router-from-openwrt-firmware-to-cudy-official-firmware?pos=1&_sid=cd51a5301&ss=r
“I’d like to work on adding official OpenWrt support for WR300, but having some trouble. Trying to access the u-boot on the WR300 using the TTL serial port, to be able to test OpenWrt images or recover factory firmware. On power-up without reset button, device boots normally and shows messages at 115200 and any characters entered are echoed back so the serial connection is working, but no Linux shell access possible. Now trying to power up the WR300 while holding the reset button, the serial console just shows some garbage which looks like wrong serial speed, but have tried all of 9600/19200/38400/57600/115200 and can’t seem to be able to see any u-boot messages, just the garbage. Does it use a non-standard serial speed and/or binary protocol (like x/y/zmodem) for recovery? Your help would be much appreciated – thanks!”
Wouln’t make more sense if Cudy would contribute to the OpenWRT project directly?
Your firmware is based on OpenWRT, so it would be a way to give back to the community and, also, facilitate a path for us, non tech-savy people, to use more up to date versions.
I understand you might want to keep you “secret sauce” under wraps, but if there’s a will, there’s a way…
Hello Cudy team,
I found that VLAN support in Cudy AP3000 is not up to the features I expected from business-oriented device (unfortunately after purchase). I would like to switch to OpenWrt (it now supports AP3000) to see if it can be done with that OS. But I found out that it will be impossible to recover to Cudy firmware, because tftp restore is not available in this AP. Do you have plans to resolve this issue with firmware update, or it is limited in hardware? Should I better return this AP and give up?
Hello my friend,
I was looking forward the latest OpenWrt 24.10.0 stable version. Finally it was released. I would like to upload it into my Cudy WR3000S v1. Should I follow your instruction above:
1/ Remove signature check from GoogleDrive.
2/ Use https://firmware-selector.openwrt.org/?version=24.10.0&target=mediatek%2Ffilogic&id=cudy_wr3000s-v1
or
to be 100% sure download OpenWrt from Cudy’s official website (but cannot find it yet)?
Regards,
Tadeusz
I’d like to work on adding official OpenWrt support for WR300, but having some trouble. Trying to access the u-boot on the WR300 using the TTL serial port, to be able to test OpenWrt images or recover factory firmware. On power-up without reset button, device boots normally and shows messages at 115200 and any characters entered are echoed back so the serial connection is working, but no Linux shell access possible. Now trying to power up the WR300 while holding the reset button, the serial console just shows some garbage which looks like wrong serial speed, but have tried all of 9600/19200/38400/57600/115200 and can’t seem to be able to see any u-boot messages, just the garbage. Does it use a non-standard serial speed and/or binary protocol (like x/y/zmodem) for recovery? Your help would be much appreciated – thanks!