1. Laadige fail alla ja pakendage see hinnast.
2. Laadige uusim püsivara ametlikust veebisaidist ja nimetage see ümber "recovery.bin". Märkus: Te peate selle panema samasse faili Tftpd tööriistade hulka.
3. Lülitage ruuter välja. Tõmmake toiteadapter välja või vajutage nuppu POWER.
4. Ühendage arvuti ruuteri LAN-porti Ethernet-kaabliga.
5. Konfigureerige oma arvuti IP-aadressi '192.168.1.88' käsitsi.
6. Käivitage 'tftp32.exe'.
7. Käivita käsureas 'netsh advfirewall set allprofiles state off', et keelata Windowsi tulemüür, muidu blokeeritakse tftp. Või lülitage tulemüür välja oma arvuti juhtpaneelis. Nagu allpool näidatud.
8. Vajutage nuppu/auku "Reset" ja hoidke seda all. Enne ruuteri sisselülitamist ja enne, kui tftp alustab püsivara allalaadimist, ärge vabastage nuppu 'Reset' / auku.
9. Lülitage ruuter sisse.
10. Kui kõik tuled vilguvad kiiresti või kui tftp hakkab püsivara alla laadima, võite vabastada nupu 'Reset' nuppu/auku.
11. Kui tuli vilgub aeglaselt, on uuendamine lõpetatud.
12. Taastage oma arvuti IP-aadress dünaamiliseks IP-ks.
13. Valmis.
242 comments
@Dear Henry,
If you purchased the item from Cudy’s official flagship store on Taobao or JD.com, you can contact customer service directly to request a replacement.
“Hi support.
1. Guys I think a comment of a blog entry is not the better way to provide tech support.
2. So I downloaded this one:
m_upgrade_TR3000-R47-2.4.21-20251009-140812-sysupgrade_90649
Both routers download the bin file and after install the router led flashes to red and stay like that. Is there something else I can do? I’m in mainland China, is it possible to give this two devices back to the factory?
Both of your router are 128MB Flash version according to the SN. So you must download the firmware for TR3000 V1.0 to recover the router. Not the firmware for TR3000 256MB Flash V1.0
“Hi support team! According to your question “please check the SN number on the label at the bottom”, so two of my devises are:
tr3000245000505 EU1.0
tr3000250202816 ZH1.0”"
Hi support.
1. Guys I think a comment of a blog entry is not the better way to provide tech support.
2. So I downloaded this one:
m_upgrade_TR3000-R47-2.4.21-20251009-140812-sysupgrade_90649
Both routers download the bin file and after install the router led flashes to red and stay like that. Is there something else I can do? I’m in mainland China, is it possible to give this two devices back to the factory?
Both of your router are 128MB Flash version according to the SN. So you must download the firmware for TR3000 V1.0 to recover the router. Not the firmware for TR3000 256MB Flash V1.0
“Hi support team! According to your question “please check the SN number on the label at the bottom”, so two of my devises are:
tr3000245000505 EU1.0
tr3000250202816 ZH1.0”
@Уважаемый Александр,
Какую прошивку вы использовали для восстановления маршрутизатора? Пожалуйста, пришлите мне название прошивки, которую вы скачали.
Кроме того, разжимали ли вы прошивку в файл с расширением «.bin» перед тем, как переименовать его?
“Здравствуйте, роутер TR3000, делаю откат с OpenWRT на прошивку cudy по инструкции, в программе показано что прошивка загрузилась, на роутере мигает индикатор с красного на белый, больше ничего не происходит, что делать?”
Здравствуйте, роутер TR3000, делаю откат с OpenWRT на прошивку cudy по инструкции, в программе показано что прошивка загрузилась, на роутере мигает индикатор с красного на белый, больше ничего не происходит, что делать?
@Dear Sergio,
Our technical support has contacted you via email. Please check.
“I have the M1800 and I have the same issue, invalid board info, when trying to revert to the Cudy firmware”