Valmistamine:
1. Paigaldage antennid ja asetage need ülespoole.
2. Sisestage SIM-kaart pessa, kuni kuulete klõpsatust.
3. Ühendage toiteadapter ruuteriga ja lülitage see sisse.
Sepp 1: Avatage veebilehitseja ja minge veebilehele http://cudy.net või http://192.168.10.1. Sisestamiseks sisestage administraatori parool.
Märkus: Kui püsivara versioon on 1.X.X. Me oleme eemaldanud vaikimisi administraatori parooli alates püsivara versioonist 2.X.X. Te peate looma administraatori parooli esimesel sisselogimisel.
Detailide saamiseks vaadake Kuidas Cudy ruuteri veebiliidesesse sisse logida?
Samm 2: Avaneb aken Quick Setup, valige oma 'Ajavöönd'.
Samm 3: Konfigureerige APN-i parameetrid. Enamasti on meil vaja lihtsalt hoida APN-profiili " Auto". Seejärel klõpsake nuppu "Järgmine". ruuter valib APN-parameetrid automaatselt. (Soovitan)
Kui soovite kohandada APN-i parameetreid. Võite valida APN-profiiliks " Käsitsi" ja sisestada õiged APN-parameetrid.
Märkus: Kui te ei ole APN parameetrite osas kindel, võtke ühendust oma internetiteenuse pakkujaga.
Kui te ei ole kindel APN parameetrite osas, võtke ühendust oma internetiteenuse pakkujaga.Samm 4: Määrake traadita võrgu nimi ja parool või hoidke need vaikimisi.
Sepp 5: Vajutage "Save & Apply", et lõpetada konfiguratsioon.
Samm 6: Kui olek on ühendatud, saate nautida internetti.
52 comments
@Dear Sakai,
You can set the metric of the WAN connection. The small the metric, the higher priority the WAN connection.
For the new firmware, it is under development currently. We will release a new firmware in the near future.
“R700 V1.0
I bought this router recently and this has never received any firmware update since its release date. Can you guys work on its latest firmware? Currently, we are unable to put multiple IP ranges when making a rule set to route specific data through a specific WAN.
Also, the rule is not applying properly sometimes. In the policy tab, you can not give priority to a specific WAN. Please fix these."
R700 V1.0
I bought this router recently and this has never received any firmware update since its release date. Can you guys work on its latest firmware? Currently, we are unable to put multiple IP ranges when making a rule set to route specific data through a specific WAN.
Also, the rule is not applying properly sometimes. In the policy tab, you can not give priority to a specific WAN. Please fix these.
@Dear Tommy,
Generally, there is no need to set the router. Just connect the devices to the LAN ports of the router. Then it will work. You can try to reset the router to factory default by long pressing the reset button for about 3 seconds. You can release the reset button when the LED flashes. Then connect all the devices and check if the problem avoided?
In addition, please check if the CCTV camera is set to get the IP address via DHCP when connect to the router via wired cable? If not, please set it.
“Dear Cudy team. How should I configure your router lt500D to be able to connect two CCTV cameras via Ethernet cable? I was able to connect only one that supports wifi, second one can be connected only via cable. Your router does not see these devices in lan network.”
Dear Cudy team. How should I configure your router lt500D to be able to connect two CCTV cameras via Ethernet cable? I was able to connect only one that supports wifi, second one can be connected only via cable. Your router does not see these devices in lan network.
@Dear Amigos,
The AT command for checking EARFCN is AT+QENG=“servingcell” , You can also check it in the syslog. For example
AT+QENG=“servingcell” → AT+QENG=“servingcell” +QENG: “servingcell”,“NOCONN”,“LTE”,“FDD”,250,01,41720C,9,1802,3,5,5,454C,-89,-10,-59,14,35 OK
The “1802” is the EARFCN.
For cell ID, we don’t have plan to change the format.
“Hi! In first iam need to say thanks for very balanced products with Cudy brand. Anyway i have some question about Cudy LT400 Outdoor functions.
1 – in Status we have data about LTE connection as MCC MNC CID and PCID, but not EARFCN and not eNodeB ID. How i can get it? Modem have this data by cell.
2- Cell ID have hex format. possible convert it in dec format Base ID?
and very important
need AT commands LIST for internal modem.
Thanks!"