Cudy Whole Home Mesh süsteem on loodud selleks, et kõrvaldada surnud tsoonid ja tagada katkematu Wi-Fi kogu teie kodus. See artikkel juhendab teid samm-sammult võrgusüsteemi ehitamisel.
Esvalmistus:
1. Veenduge, et teil on vähemalt 2 Cudy toodet.
2. Kõik Cudy tooted toetavad mesh-tehnoloogiat: Home Mesh-Cudy ametlik veebisait
3. Firmware on ajakohane: Download Center
4. Võtke need seadistamise ajal samasse ruumi.
5. Võtke need samasse ruumi. Lähtestage kõik oma Cudy tooted tehaseseadetele. (Kui seade on sisse lülitatud, vajutage ja hoidke RESET-nuppu koos näpuga 6s jooksul all, seejärel laske lahti.)
6. Seadistage oma esmane ruuter ja ühendage see internetiga.
Kui näited on M1800 ja WR2100:
Samm 1: Avage veebilehitseja ja minge veebilehele http://cudy.net või http://192.168.10.1.
Üksikasjalikumalt vt Kuidas Cudy Routeri veebiliidesesse sisse logida?
Samm 2: Vajutage süsteemi oleku lehel nupule "+".
Samm 3: Vajutage M1800-l WPS-nuppu ja seejärel WR2100-l WPS-nuppu.
Pääsevõrguüksus: Välkvalge
lisavõrguüksus: Vilgub vaheldumisi valge ja punane
Samm 4: See läheb "Scanning", seejärel " Connecting".
Samm 5: Oodake, kuni lisaruuteri süsteemi LED muutub helesiniseks, seejärel paigutage WR2100 ümber.
Samm 6: Edu ja naudi võrgusilma võrku.
Märkus:
1. 4/5G ruuterit saab seadistada ainult peamise võrgusilmaüksusena. Näiteks:
2. Te ei saa sisse logida lisavõrgu võrgusilma ruuteri veebiliidesesse. Kui soovite seadeid muuta, klõpsake "Süsteemi olek"->"Mesh".
79 comments
Tengo un router del proveedor que me genera una red wifi, tengo tres Cudy M3000 wifi y quiero por medio de cable ethernet repitan la red wifi del router del proveedor con el mismo nombre y la misma contraseña
@Dear John,
1. Please check if the Mesh system is installed. You can login to the web page of the main mesh router, check the “Mesh” status card.
2. If yes, please check the status page of the satellite mesh router. Check if the backhaul is Wired?
3. If the backhaul is wired, please try to change the cable between the two router. Do you connect them directly or there is a switch between them?
4. What is the firmware version of the two routers? Please update to the latest and check again.
“I have two WR11000s which I’m trying to use as a mesh. The main router is connected to 1 Gbps fibre WAN. The secondary router is connected to the main router by wired ethernet (cat 6 cable).
When I plug my laptop into the secondary router with ethernet, I get a great connection (~800+ Mbps, according to speedtest.net). When I connect to the secondary router by wifi, the connection is hopeless — even sitting my laptop right next to the router, I get speeds of just a couple of Mbps, and lots of drop outs. This happens on all bands (2/5/6 GHz).
When I am connected to the main router by wifi, it works fine.
Any suggestions as to what might be going wrong?
Thanks!"
I have two WR11000s which I’m trying to use as a mesh. The main router is connected to 1 Gbps fibre WAN. The secondary router is connected to the main router by wired ethernet (cat 6 cable).
When I plug my laptop into the secondary router with ethernet, I get a great connection (~800+ Mbps, according to speedtest.net). When I connect to the secondary router by wifi, the connection is hopeless — even sitting my laptop right next to the router, I get speeds of just a couple of Mbps, and lots of drop outs. This happens on all bands (2/5/6 GHz).
When I am connected to the main router by wifi, it works fine.
Any suggestions as to what might be going wrong?
Thanks!
@Dear Kamil,
I think the camera is connected to the 2.4GHz WiFi of the router. You can try to change the mode of 2.4GHz to 802.11b+g+n mode. Then check if the camera is able to connect to it?
“I built a mesh network using four WR3600E routers, and the internet works great. However, this network was meant for cctv monitoring, and that’s where the problem appeared: when the routers are in mesh mode, the cameras won’t log into the network, no matter which WPA level we choose. Only after disabling encryption and the password do the cameras connect to Wi-Fi. The cameras are XMeye. Is there any solution? When connected to lan port everything works. I’ll add that when the router is not in mesh mode, the same camera connects to it normally with wifi. Regards.”
I built a mesh network using four WR3600E routers, and the internet works great. However, this network was meant for cctv monitoring, and that’s where the problem appeared: when the routers are in mesh mode, the cameras won’t log into the network, no matter which WPA level we choose. Only after disabling encryption and the password do the cameras connect to Wi-Fi. The cameras are XMeye. Is there any solution? When connected to lan port everything works. I’ll add that when the router is not in mesh mode, the same camera connects to it normally with wifi. Regards.