Cudy Whole Home Mesh system is built to eliminate dead zones and to provide uninterrupted Wi-Fi throughout your home. This article will guide you to build a mesh system step by step.
Preparation:
1. Ensure you own at least 2 Cudy products.
2. All Cudy products support mesh technology: Home Mesh-Cudy official website
3. Firmware is up-to-date: Download Center
4. Take them in the same room during configuration.
5. Reset all your Cudy products to factory default settings. (With the Power on, press and hold the RESET button with a pin for 6s, then release.)
6. Set up your primary router and make it connect to the internet.
Here we take M1800 and WR2100 as examples:
Step 1: Open a web browser and go to http://cudy.net or http://192.168.10.1.
For details, please refer to How to log into the web interface of Cudy Router?
Step 2: On the System Status page, click on the "+" button.
Step 3: Press the WPS button on the M1800 and then press the WPS button on WR2100.
Main mesh unit: Flash white
Add-on mesh unit: Flash white and red alternately
Step 4: It will go to "Scanning", then " Connecting".
Step 5: Wait until the System LED of the add-on router turns into solid blue, then relocate WR2100.
Step 6: Success and enjoy the mesh network.
Note:
1. 4/5G router can only be set up as a Main mesh unit. For example:
2. You will not able to log into the web interface of the add-on mesh router. If you want to change settings, please click on "System Status"->"Mesh".
72 comments
Subject: Mesh Configuration with LT500 and WR1300 Routers
Dear Support Team,
I understand that the LT500 can only function as a main Mesh router and cannot be used as a satellite node.
I currently have three routers:
LT500
WR1300
LT500
Two of the LT500 units have access to the internet via 4G.
Is it possible to set up a Mesh network where all three devices are working together?
For example:
LT500 (main) + WR1300 (satellite)
The second LT500 (also with 4G) + the same WR1300 (as a satellite again)
In other words, can the same WR1300 be linked as a Mesh satellite to two separate LT500 routers?
Thank you for your assistance.
@Tahseen,
We suggest 8 nodes.
“Hello, how many Cudy M3000 V2 AX3000 V2.0 https://www.cudy.com/products/m3000-2-0 can be used in a Mesh environment? Is there any threshold to signal strength (RSSI). Thanks, Tahseen”
@Andre van der weide,
Sorry for the inconvenience caused to you!
Please set the SSID of M3000 separately on 2.4GHz and 5GHz. Then connect to the 5GHz WiFi if the clients support 5GHz. The 2.4GHz is not as good as the 5GHz if the signal strength is weak.
“I have m3000 cudy mesh units i don’t know if version 1 ore 2.
5ghz working perfect but 2.4 mhz the network is sometimes found and connect but no internet connection. i have the latest firmware 2.3.8 on al 3 cudy’s
My wife get angry every time because no connection on phone and switching off wifi”
@Dear Fouad,
Yes, you can install mesh system with them via Wi-Fi or wired cable.
“I want to know if i buy 3x WR3000, if i can use them in MESH mode?”
Hello, how many Cudy M3000 V2 AX3000 V2.0 https://www.cudy.com/products/m3000-2-0 can be used in a Mesh environment? Is there any threshold to signal strength (RSSI). Thanks, Tahseen