1. Download and unzip the file from here.
2. Download the latest firmware from the official website and rename it to 'recovery.bin'. Note: You must put it in the same file of Tftpd tools.
3. Power off your Router. Unplug the power adapter or press the POWER button.
4. Connect your computer the Router's LAN port with an Ethernet cable.
Note: Only one model is an exception: the TR1200. The WAN port must be connected during firmware recovery. All other models use the LAN port.
5. Configure your computer's IP address to be '192.168.1.88' manually.
6. Run 'tftp32.exe'.
7. Run 'netsh advfirewall set allprofiles state off' in the command line to disable Windows firewall, otherwise tftp will be blocked. Or you can disable the firewall on the Control Panel of your computer. As shown below.
8. Press the 'Reset' button/hole and hold it. Before the Router is powered on and before tftp start to download the firmware, don't release the 'Reset' button/hole.
9. Power on the Router.
10. When the Lights are all flashing fast, or when tftp start to download the firmware, you can release the 'Reset' button/hole.
11. When the light flashes slowly, the upgrade is complete.
12. Please recover your computer's IP address to be dynamic IP.
13. Done.
165 comments
@Привет, Денис!
TFTP-утилита часто распознаётся как вирус. Предлагаю вам найти её самостоятельно. Я не могу отправить её по электронной почте. Или свяжитесь со мной через WhatsApp. Я могу отправить её через WhatsApp.
“Ссылки не работают, судя по комментариям компания больше не хочет что бы люди пользовались их ПО?
Я хочу восстановить официальную прошивку на WR3000S, как мне это теперь сделать?”
hi i am having exactly the same flash issue from openwrt as alan for the 256mb cudy, i follow the instructions and download the 2.3.9. firmware for 256mb cudy tr3000. The router kept flashing red and white after going through the tftp for recovery
Ссылки не работают, судя по комментариям компания больше не хочет что бы люди пользовались их ПО?
Я хочу восстановить официальную прошивку на WR3000S, как мне это теперь сделать?
@Dear Alan,
Our technical support has contacted you via email. Please check.
“Thank you for your response. However, it did not resolve my issues.
Currently, my TR3000-256MB router when in a normal boot state. After plugging in the power cable, the red and white LEDs keep flashing, and my computer’s LAN connection is continuously going on and off. I attempted to set a static IP address of 192.168.1.2 on my computer, but I cannot ping or connect to the router’s webpage at 192.168.1.1.
When I try to use TFTP, the router does not respond to my computer’s IP (192.168.1.88), but it does respond to 192.168.1.2. After sending the recovery.bin file (downloaded from the mainland webpage: TR3000_256MB_Flash-R103-2.3.9-20250208-171917-sysupgrade.bin) to the router, it does not reboot on its own, and the LEDs continue to flash red and white.
The loop is continuous. Am I flashing the correct file? Is there any other way to restore the factory firmware?"
Thank you for your response. However, it did not resolve my issues.
Currently, my TR3000-256MB router when in a normal boot state. After plugging in the power cable, the red and white LEDs keep flashing, and my computer’s LAN connection is continuously going on and off. I attempted to set a static IP address of 192.168.1.2 on my computer, but I cannot ping or connect to the router’s webpage at 192.168.1.1.
When I try to use TFTP, the router does not respond to my computer’s IP (192.168.1.88), but it does respond to 192.168.1.2. After sending the recovery.bin file (downloaded from the mainland webpage: TR3000_256MB_Flash-R103-2.3.9-20250208-171917-sysupgrade.bin) to the router, it does not reboot on its own, and the LEDs continue to flash red and white.
The loop is continuous. Am I flashing the correct file? Is there any other way to restore the factory firmware?