Introduction
This article lists both the latest and historical updates to the Cudy Software Platform (CSP), starting from version 2.3 to 2.5. It provides an overview of newly introduced features and the Cudy models they support.
You are welcome to leave comments and suggest new features under this article. We will be happy to review your ideas and prioritize the most requested or most unique ones for our R&D roadmap.
Where to download the latest firmware?
You will receive upgrade notice on Cudy App, or you can check if there is 2.5 firmware available for your model at www.cudy.com/download
How to upgrade the firwmare on Cudy devices: Read this FAQ.
CSP 2.5
Release Time
Starting from February 2026
Support Plan (Ranked with priority)
M3000 1.0, M3000 2.0, WR3000 1.0, WR3000 2.0, WR3000S 1.0, WR3000E 1.0, TR3000 1.0, WR11000 1.0, WR6500 1.0, WR6500H 1.0, WR3600 1.0, WR3600E 1.0, WR3600H 1.0, M11000 1.0, M3600 1.0, WR1300 3.0/4.0, WR1200E 1.0, WR1200 2.0/2.1, M1300 3.0, M1200 1.0, P4 1.0, LT700 2.0, LT500 3.0, LT500D 3.0, LT300 V3.0, LT700 Outdoor 2.0, LT500 Outdoor 2.0
You may not receive the upgrade immediately on your deive as the update plan on different models vary.
Updated on 13 Feb 2026: We have received feedback regarding support for models not included in the plan above. Please rest assured that some popular models require additional development due to their hardware design and are therefore not listed at this time. We sincerely appreciate your feedback and understanding.
Features
|
Function
|
Supported Devices
|
Page Screenshot
|
|---|---|---|
|
Mesh Topology
Display the connection topology between Mesh devices (client devices will not be displayed) on the Mesh Details page
|
Cudy Mesh-compatible models
|
 |
|
Select Mesh Backhaul
Satellite Mesh devices can be configured to operate only in wired backhaul mode
This helps prevent possible loops: when multiple Cudy APs are powered by a PoE switch, and the PoE switch is powered off and on, some APs may establish wireless backhaul and provides network from the LAN port, causing loop similar as such topology switch1 -- AP1 ))(( AP2 -- switch1
|
Cudy Mesh-compatible models
|
-
|
|
Select the Mesh upstream device
Mesh satellite devices now allow scanning for nearby mesh nodes, selecting a specific node to connect to. It will switch to automatic upstream mesh selection only if the chosen node cannot be found in the future.
|
Cudy Mesh-compatible models
|
 |
|
Multiple VPN Servers
Supports simultaneously enabling multiple VPN servers with different protocols
(IPsec and Zerotier cannot be enabled simultaneously with other VPNs)
|
All Wi-Fi Router/Mesh System models
(excluding models with 8MB Flash)
|
 |
|
Multiple VPN Client Configs
Supports configuring multiple VPN Clients, but only one can be enabled at a time
|
All Wi-Fi Router/Mesh System models
(excluding models with 8MB Flash)
|
 |
|
L2TP/PPTP supports multiple Accounts
L2TP/PPTP VPN server supports configuring multiple accounts
|
All Wi-Fi Router/Mesh System models
(excluding models with 8MB Flash)
|
 |
|
VPN Configuration Migration
Supports backing up VPN configurations and restoring them on another device, allowing configuration restoration across different device models. Only supports migrating all VPNs together.
|
All Wi-Fi Router/Mesh System models
(excluding models with 8MB Flash)
|
 |
|
Global Default Speed Limit
QoS adds default rate limit settings, and all Clients are subject to the default rate limit
|
Wi-Fi Routers
|
 |
|
Guest Network Speed Limit
Supports setting the uplink and downlink bandwidth of the entire Guest Network
|
Wi-Fi Routers
|
 |
|
New Firmware Reminder
When a new firmware is detected, the page will pop up a new firmware upgrade reminder when entering the config web page
|
All Models
|
-
|
|
Manually execute WoL
Wake on LAN changed to manual execution
|
All Models
(Some low-end models do not have this feature)
|
 |
|
DHCP Adds Gateway Setting
|
All Wi-Fi Router/Mesh System models
|
 |
|
Account Logout
Supports account logout
|
All Models
|
-
|
|
OpenVPN Speed Boost
Supports OpenVPN DCO, enhancing the maximum upload and download speeds of OpenVPN
|
MTK AX3000 Model
WR3000 1.0
WR3000S 1.0
WR3000E 1.0
TR3000 1.0
|
-
|
|
Displays IPTV Settings during Quick Setup
Advanced in QuickSetup unhides the IPTV menu
|
All Wi-Fi Router/Mesh System models
|
 |
|
Menu Entry Position Adjustment
Adjust the General Settings menu and the Advanced Settings menu:
Move the entries of IPTV/VLAN and Guest Network into General Settings;
Move the entry of Captive Portal into Advanced Settings
|
All Models
|
  |
|
Accessibility Features
Add accessibility features and support contrast adjustment
|
All Models
|
 |
|
WPS ON/OFF
Add WPS Switch
|
All Models
|
 |
|
Packet Capture
Add packet capture functionality to the diagnostic tool
|
All Wi-Fi Router/Mesh System models
(excluding models with 8MB Flash)
|
 |
|
DoH
Add DNS over HTTPS mode for custom DNS
|
All Wi-Fi Router/Mesh System models
(excluding models with 8MB Flash)
|
 |
|
TW Region Code
Added support for TW Region code, 2.4G channels 1-11, 5G channels band1, band2, and band4
|
All Models
|
-
|
|
TW IPTV
Add IPTV Taiwan CHT Mode
|
All Wi-Fi Router/Mesh System models
|
 |
|
DNS Online Detection
The online detection function adds DNS protocol detection method
|
All Wi-Fi Router/Mesh System models
|
-
|
CSP 2.4
Release Time
First released on WR3000 on April 28, 2025
Main Functions
|
Function
|
Supported Devices
|
Page Screenshot
|
|---|---|---|
|
Compatible with APP 1.3
|
All wireless devices
|
Refer to APP 1.3 Features
|
|
Optimize EAEU translation
|
All wireless devices
|
|
CSP 2.3
Release Time
First released on AP1300D on December 31, 2024
Main Functions
|
Function
|
Supported Devices
|
Page Screenshot
|
|---|---|---|
|
Multi-SSID
Supports configuring multiple SSIDs
|
Commercial Wireless AP
|
 |
|
Captive Portal
After the phone connects to Wi-Fi, the authentication page automatically pops up, and authentication is required to access the Internet
Supports customizing the content of the authentication page, such as background images, logos, font colors, and terms of service.
Supported authentication methods are: 1) One-click authentication; 2) Password input authentication
|
Commercial Wireless AP
|
 |
|
USB Tethering
Controls whether the USB interface enables network sharing. Once enabled, the device can be used to extend the wireless network of a mobile phone or a portable Wi-Fi
|
Devices with USB ports, such as TR3000
|
 |
|
Wi-Fi Control
Turn on the hardware button on the rear panel AP to simultaneously control the on/off of the LED and Wi-Fi. At this time, toggling the LED via software will also trigger the synchronous on/off of Wi-Fi.
|
Wall AP
|
 |
|
PoE Passthrough
Whether the AP port of the control panel can supply power externally (only available under 802.at power reception, default is off)
|
Wall AP
|
 |
262 Kommentare
Hi,
Recently you launched a new firmware for cudy wr3000s v1. Firmware- 2.5.28.
But this firmware has issue on smart connect as the previous globally released firmware.
When smart connect is turned on and router push devices to 2.4ghz from 5 ghz, devices disconnect from wifi amd then reconnect.
Can you make a beta firmware where router will not push devices, because modern devices automatically shift themself to the strongest signal.
If router pushes and devices also decides, there collision happens and devices disconnect.
Make a beta firmware where the router will simply make the 2.4 ghz and 5ghz wifi name and password same, nothing else.
Router will not force or push device to shift from 2.4ghz to 5ghz and 5ghz to 2.4ghz.
Then this disconnection issue will not happen. When the beta firmware is ready please send me the firmware through gmail.
Please i badly need to use samrat connect without any disconnection issue.
Can you send me the beta firmware for M11000. Thank you
Subject: Comprehensive Bug Report & Request for Beta Firmware – Cudy M3000 (v2.5.28)
Dear Cudy Support Team,
I am writing to consolidate all the issues I am experiencing on my Cudy Mesh Network after updating the main router to firmware version v2.5.28.
Please note that I have already performed a factory reset on the main M3000 router as well as all sub-nodes and reconfigured the entire network from scratch, but none of the issues were resolved.
1. Network Topology Setup
All units are connected in a Daisy-Chain Wired Mesh setup (Ethernet Backhaul) as follows:
Main Mesh Router: Cudy M3000 (v2.5.28)
2nd Node: Cudy M1200
3rd Node: Cudy M1500 (v2.3.12Beta)
4th Node: Cudy M1300
2. Detailed Description of Issues
Issue 1: Connected Client Count Shows “0” in Topology
In the main M3000 mesh topology view, the 3rd node (M1500) and 4th node (M1300) constantly show 0 connected clients, even though multiple active wireless and wired devices are connected to them.
Issue 2: Real-Time Traffic Data Displays “0.0 Kbps”
Upload and download traffic speeds for devices connected to the sub-nodes (M1500 and M1300) are not displaying anywhere.
On the main M3000 dashboard client list, traffic speed for these clients shows 0.0 Kbps.
Even when logging directly into the dedicated individual Web UI/dashboards of the M1500 and M1300 nodes, all connected devices still show 0.0 Kbps.
Issue 3: Ad Shield (AdGuard DNS) Counter Not Updating
Under the Ad Shield settings (AdGuard DNS), the “24h Blocked Request” counter never updates and remains stuck at 0/0, despite AdGuard DNS being enabled and actively processing requests.
3. Key Context
All of these features (Topology Client Count, Real-Time Traffic Speed, and Ad Shield Counter) were working perfectly on firmware version v2.5.10.
These bugs were introduced immediately after upgrading to v2.5.28.
Since these issues significantly affect my daily network management, please forward this specific multi-model daisy-chain setup details to your R&D team.
I kindly request an update or a patched test/beta firmware to resolve these bugs.
Looking forward to your support.
Best regards,
Abir Hasan Riad
@Dear Rick,
Our technical support has contacted you via email. Please check.
“Hi, On 31st July one month ago I asked about the release date for CSP 2.5 for Cudy 3000 V1 and you replied ( @Dear Rick Green,
I think it will be soon. I will try to push it.
“Hi, I see that WR3000 V 1.0 had priority for update to CSP 2.5 back in February 2026 but has not recieved it yet . When do you plan on releasing the update for this router ? CSP 2.5 has new features I badly need and I do not want to have to go to full OPENWRT . Best regards Rick "
support July 31, 2026 )
This router was supposed to be among the first to receive V 2.5 back in February but in spite of your promises that it is coming soon nothing has appeared . Why the long delay ?
Best regards
Rick"
Hi, On 31st July one month ago I asked about the release date for CSP 2.5 for Cudy 3000 V1 and you replied ( @Dear Rick Green,
I think it will be soon. I will try to push it.
“Hi, I see that WR3000 V 1.0 had priority for update to CSP 2.5 back in February 2026 but has not recieved it yet . When do you plan on releasing the update for this router ? CSP 2.5 has new features I badly need and I do not want to have to go to full OPENWRT . Best regards Rick "
support July 31, 2026 )
This router was supposed to be among the first to receive V 2.5 back in February but in spite of your promises that it is coming soon nothing has appeared . Why the long delay ?
Best regards
Rick