Перед настройкой
1. Убедитесь, что усилитель подключён к роутеру.
2. Войдите в веб-интерфейс усилителя, перейдите в раздел Дополнительные настройки и включите параметр Повторитель MAC-адресов.
Усилитель создаёт виртуальный MAC-адрес для каждого клиентского устройства. Роутер принимает такие виртуальные MAC-адреса клиентских устройств за реальные, поэтому в правилах флиьтрации MAC-адресов роутера необходимо указывать именно виртуальные MAC-адреса.
Настройка
Шаг 1. Найдите реальный MAC-адрес компьютера (пример: 74-86-E2-0E-0D-87). MAC-адрес также можно найти в списке клиентов усилителя.
Примечание. На большинстве телефонов используется случайно сгенерированный MAC-адрес. Необходимо предварительно изменить MAC-адрес телефона со случайно сгенерированного на реальный в настройках WLAN телефона.
Шаг 2. Проверьте MAC-адрес компьютера через веб-интерфейс роутера. Будет отображаться виртуальный MAC-адрес компьютера (пример: B2:4B:D6:0E:0D:87).
Шаг 3. Роутер видит только виртуальный MAC-адрес компьютера и не видит его реальный MAC-адрес, при этом независимо от типа MAC-адреса последние шесть символов (без учёта разграничительных знаков) будут совпадать.
Реальный MAC-адрес: 74:86:E2:0E:0D:87
Виртуальный MAC-адрес: B2:4B:D6:0E:0D:87
Шаг 4. Найдите реальный MAC-адрес усилителя (напечатан на этикетке на нижней панели устройства) и запишите его (пример: B4:4B:D6:25:FE:C4).
Откройте список клиентов роутера, у усилителя будут следующие MAC-адреса: B2:4B:D6:25:FE:C4 и B2:4B:D6:25:FE:C6.
Примечание. Если используется двухдиапазонный усилитель, то в правила фильтрации MAC-адресов роутера надо будет добавить два MAC-адреса усилителя.
Шаг 5. Выберите параметр Разрешить только перечисленные и добавьте MAC-адреса устройств, для которых нужно сохранить доступ в интернет.
Комментариев: 2
@Dear Afeef,
There are two settings may override the MAC Filter.
1. SPI Firewall. Enabled by default. If you disable it on the web page. The MAC Filter will not work.
2. IPv6. The firewall is not working on IPv6 traffics now. So If you enable the IPv6 function. The IPv6 traffics will still work even if you enable the MAC filter function. You can disable IPv6 and check again.
“Dear Cudy Technical Support,
I have a problem with the MAC Filter function on my Cudy router, and I would appreciate your technical clarification.
Router model:
Cudy WR3000 V1.0
Firmware version:
2.4.19-20250829-192837
Operating mode:
Main Router Mode"
Dear Cudy Technical Support,
I have a problem with the MAC Filter function on my Cudy router, and I would appreciate your technical clarification.
Router model:
Cudy WR3000 V1.0
Firmware version:
2.4.19-20250829-192837
Operating mode:
Main Router Mode
The problem is that when I add a device’s MAC address to the MAC Filter blacklist/block list, the device is not blocked from Internet access. The device remains connected to the Wi-Fi and can still access the Internet normally.
I have already verified the following:
The router is operating in Main Router Mode. I am using the MAC address shown by the router in the connected devices/client list. The MAC address is added to the MAC Filter block list. MAC Filter is enabled. I applied/saved the configuration. I disconnected and reconnected the client to Wi-Fi after applying the rule. The client still has full Internet access.I am not referring to the Parental Control/Web Filter or domain blacklist. My issue is specifically with the MAC Filter / MAC Access Control function, where I expect a blocked MAC address to lose Internet access.
Could you please clarify:
1. Is MAC Filter fully supported and working on WR3000 V1.0 with firmware 2.4.19?
2. When using “Allow all except listed”, should a listed MAC address be completely prevented from accessing the Internet?
3. Are there any known bugs or limitations with MAC Filter in firmware 2.4.19?
4. Does MAC Filter behave differently between the 2.4 GHz and 5 GHz networks?
5. Does the MAC Filter work differently when Private/Random MAC Address is used by the client?
6. Are there any other settings that could override or bypass the MAC Filter?
7. If this is a firmware issue, is there a newer beta firmware or recommended workaround that fixes it?
I would appreciate it if you could explain why the blocked device is still able to access the Internet and provide the correct configuration or troubleshooting steps.
Thank you for your support.
Best regards,
Afeef