Avisos
Esta página lista softwares de dispositivos compatíveis com o sistema OpenWrt. Antes de baixar e instalar o software, observe que o Projeto OpenWrt é um sistema operacional Linux voltado para dispositivos embarcados. Em vez de tentar criar um firmware único e estático, o OpenWrt oferece um sistema de arquivos totalmente gravável com gerenciamento de pacotes. Isso o libera da seleção e configuração de aplicativos fornecidas pelo fornecedor e permite que você personalize o dispositivo por meio do uso de pacotes para se adequar a qualquer aplicação. Para desenvolvedores, o OpenWrt é a estrutura para construir um aplicativo sem a necessidade de construir um firmware completo em torno dele; para usuários, isso significa a capacidade de personalização completa, para usar o dispositivo de maneiras nunca antes imaginadas.
Descrição
- Este arquivo só pode ser usado quando o seu roteador funciona na interface web do Cudy.
- Se o roteador já estiver funcionando com a interface OpenWRT, o usuário deverá restaurá-lo para o firmware oficial da Cudy primeiro. Em seguida, atualizar o roteador com este firmware.
- Como restaurar o roteador para o firmware oficial da Cudy? Leia o arquivo leia-me no arquivo baixado.
Garantia:
Cudy declara por meio deste
- Nós, da Cudy, não oferecemos garantia para nenhum software que não seja lançado pela Shenzhen Cudy Technology Co., Ltd.
- Não assumimos nenhuma garantia para produtos que tenham instalado qualquer software não lançado pela Shenzhen Cudy Technology Co., Ltd.
- Se você precisar usar o software openwrt, sugerimos que você o baixe do site oficial da Cudy.
Baixe o firmware OpenWrt para remover a verificação de assinatura:Dirigir
Localizador de firmware OpenWrt (não lançado pela Cudy):Seletor de Firmware OpenWrt
1319 comentários
@Dear conrad,
Our technical support has sent you the new intermediate firmware via email. Please check.
“Dear Support !
I have already connected the serial port and restored the functionality of the cudy AP3000_P v1.
But your transition firmware does not have a recovery mode and does not support the new Motorcomm YT8821 PHY LAN chip.
Could you provide an updated version of the transition firmware for openwrt so that I do not have to restore the access point using the serial port in the future?"
Hello support!
I was create prereleased OpenWRT binary for Cudy WR1300S.
This kernel https://github.com/5yoda5/openwrt/releases/download/first_release/openwrt-ramips-mt7621-cudy_wr1300s-initramfs-kernel.bin
and Sysupgrade https://github.com/5yoda5/openwrt/releases/download/first_release/openwrt-ramips-mt7621-cudy_wr1300s-squashfs-sysupgrade.bin
Can you make intermediate transition firmware to switch from stock firmware to OpenWRT ?
Hello Cudy Support,
Could you please send me the intermediate firmware for the AP3000D?
I would like to test installing custom OpenWRT firmware.
Best regards
Dear Support !
I have already connected the serial port and restored the functionality of the cudy AP3000_P v1.
But your transition firmware does not have a recovery mode and does not support the new Motorcomm YT8821 PHY LAN chip.
Could you provide an updated version of the transition firmware for openwrt so that I do not have to restore the access point using the serial port in the future?
@Dear conrad,
The only way to restore it is to remove the AP’s cover, solder the serial port, and then connect the serial port to restore it. Is it possible for you? If yes, we can offer you the instruction to recover it via the serial port.
“Dear Support !
Purchased AP3000_P v1 access point.
Tried to flash according to the instructions from your website in openwrt through the transition firmware taken from you on google drive.
After flashing to the transition firmware, the access point lost access via lan cable ( wifi is not enabled ).
On the openwrt website found information:
As of jan. 2026, some devices are shipped with an alternate chip for single LAN port.
Now the access point is not available via lan or wi-fi.
I also can’t download the factory firmware via Recovery using the instructions on your website because the lan port is still not available.
What should I do to get the access point back online?"