1. Baixe e descompacte o arquivo deaqui.
2. Baixe o firmware mais recente dosite oficiale renomeie-o para 'recovery.bin'.Nota: Você deve colocá-lo no mesmo arquivo das ferramentas do Tftpd.
3. Desligue o roteador. Desconecte o adaptador de energia ou pressione o botão POWER.
4. Conecte seu computador à porta LAN do roteador com um cabo Ethernet.
5. Configure manualmente o endereço IP do seu computador como '192.168.1.88'.
6. Corra 'tftp32.exe'.
7. Corra 'netsh advfirewall desativa o estado de todos os perfis' na linha de comando para desabilitar o firewall do Windows, caso contrário, o tftp será bloqueado. Ou você pode desabilitar o firewall no Painel de Controle do seu computador. Como mostrado abaixo.
8. Pressione o botão 'Reiniciar' botão/orifício e segure-o. Antes de ligar o roteador e antes que o tftp comece a baixar o firmware, não solte o botão 'Reiniciar' botão/buraco.
9. Ligue o roteador.
10. Quando todas as luzes estiverem piscando rapidamente, ou quando o tftp começar a baixar o firmware, você pode soltar o 'Reiniciar' botão/buraco.
11. Quando a luz piscar lentamente, a atualização estará concluída.
12. Recupere o endereço IP do seu computador para um IP dinâmico.
13. Pronto.
230 comentários
Good day. I was able to restore the firmware using these instructions, but when the router reboots, it resets the settings, and when connecting, I have to reset the password and run the setup wizard. I restored the firmware after using OpenWrt. What could be the cause and how can I fix it?
@Dear Dany,
This is the correct article for recovering the router. You must connect the LAN port of the router to the computer when recovering. If you follow all the steps, but still don’t work. The uboot of the router may have been changed. Or the router is faulty. If you still can login to the web page of the router, you must change the uboot to Cudy official uboot first.
“Hello,
I am trying to reset and recover my Cudy TR30 router using TFTP64, but it does not work correctly.
When I connect the power and hold the RESET button, TFTP64 automatically switches the server interface to “Software Loopback Interface 1”. After that, nothing happens and the router does not start the recovery or firmware upload process.
I already tried:
Holding the RESET button before powering on Using different Ethernet ports Changing network adapter settings Setting a static IP address on my PC
However, the router still does not enter proper recovery mode.
Could you please help me understand:
1. How to correctly enter recovery/TFTP mode on the TR30
2. Which LAN port should be used
3. What IP settings are required
4. Whether this behavior indicates a hardware issue
Thank you."
Hello,
I am trying to reset and recover my Cudy TR30 router using TFTP64, but it does not work correctly.
When I connect the power and hold the RESET button, TFTP64 automatically switches the server interface to “Software Loopback Interface 1”. After that, nothing happens and the router does not start the recovery or firmware upload process.
I already tried:
Holding the RESET button before powering on Using different Ethernet ports Changing network adapter settings Setting a static IP address on my PCHowever, the router still does not enter proper recovery mode.
Could you please help me understand:
1. How to correctly enter recovery/TFTP mode on the TR30
2. Which LAN port should be used
3. What IP settings are required
4. Whether this behavior indicates a hardware issue
Thank you.
@Уважаемый Макс,
Если у вас не получается, попробуйте обратиться за помощью к кому-нибудь еще.
“Модель WR3000E , решил обновить openwrt до последний версии, роутер ушёл в циклическую перезагрузку , мигают все индикаторы. При зажатии reset , загорается следующий за индикатором питания и мигает примерно раз в секунду, по инструкции сделать не получилось.”
Модель WR3000E , решил обновить openwrt до последний версии, роутер ушёл в циклическую перезагрузку , мигают все индикаторы. При зажатии reset , загорается следующий за индикатором питания и мигает примерно раз в секунду, по инструкции сделать не получилось.