Ubrīdinājumi
Šajā tīmekļa vietnē ir uzskaitīta ierīču programmatūra, kas atbalsta OpenWrt sistēmu, pirms lejupielādējiet un instalējiet programmatūru, lūdzu, ņemiet vērā, ka OpenWrt projekts ir Linux operētājsistēma, kas paredzēta iegultajām ierīcēm. Tā vietā, lai mēģinātu izveidot vienotu, statisku programmaparatūru, OpenWrt nodrošina pilnībā rakstāmu failu sistēmu ar pakešu pārvaldību. Tas atbrīvo jūs no ražotāja nodrošinātās lietojumprogrammu atlases un konfigurācijas un ļauj jums pielāgot ierīci, izmantojot paketes, lai tā atbilstu jebkurai lietojumprogrammai. Izstrādātājiem OpenWrt ir ietvars, kas ļauj izveidot lietojumprogrammu bez nepieciešamības ap to veidot pilnu programmaparatūru; lietotājiem tas nozīmē iespēju pilnībā pielāgot ierīci, lai to izmantotu tā, kā nekad nav iedomājušies.
Apraksts
- Šo failu var izmantot tikai tad, ja maršrutētājs darbojas ar Cudy tīmekļa lietotāja saskarni .
- Ja maršrutētājs jau darbojas ar OpenWRT UI, lietotājam vispirms jāatjauno to uz Cudy oficiālo firmware. Un pēc tam atjaunināt maršrutētāju ar šo programmaparatūru. .
- Kā atjaunot maršrutētāju uz Cudy oficiālo programmaparatūru? Lūdzu, izlasiet lejupielādētajā failā esošo readme. .
Garantija:
Cudy ar šo paziņo
- Mēs, Cudy, neuzņemamies garantiju attiecībā uz programmatūru, ko nav izlaidusi Shenzhen Cudy Technology Co., Ltd. .
- Mēs neuzņemamies nekādas garantijas produktiem, kuros ir instalēta jebkāda programmatūra, ko nav izlaidusi Shenzhen Cudy Technology Co., Ltd. .
- Ja jums ir nepieciešams izmantot openwrt programmatūru, iesakām to lejupielādēt no Cudy oficiālās vietnes. .
Saņemiet OpenWrt programmaparatūru, lai noņemtu paraksta pārbaudi: Drive
OpenWrt firmware meklētājs (nav izlaists Cudy): OpenWrt Firmware Selector
1319 comments
Dear Cudy Support team!
Can I get firmware for install Openwrt on my router:
Model: WR3000E V2.0
Current Firmware: 2.4.18-20251124-103954
Маршрутизатор WR300 V1.0 SN:WR30002549
Прошивка 2.4.19-20250828-192837
Аппаратная версия WR3000 V1.0
Прошивка которая для WR3000 V1.0 на гугл диске не подходит. Выдает ошибку.
Просьба выслать прошивку по электронной почте
@Dear Dan,
Do you remember what is firmware version before update to the OpenWrt firmware? If it was 2.4.7, you can recover it via the TFTPD tool. Please refer to this article.
https://www.cudy.com/blogs/faq/how-to-recovery-the-cudy-router-from-openwrt-firmware-to-cudy-official-firmware?pos=1&_sid=b2bfff253&ss=r
If other firmware version, please keep using the OpenWrt firmware. Can not be recovered.
“Dear Cudy support team,
I am trying to restore the factory firmware after OpenWrt on AP3000 V1.0, but I am facing a problem.
Device information:
- Model: AP3000 V1.0
- Serial number: AP3000_P251600697 EU1.0
- Current firmware: OpenWrt 25.12.0
The problem is:
When trying to flash through the openwrt web interface (without saving the settings):
I downloaded the file “AP3000-R49-2.4.7-20260115-152710-sysupgrade.bin”, but the router rejects it with the error “Invalid file”.
According to the instructions for returning: Connected directly to a PC with IP:192.168.1.10, holding reset
Connected the power. But in this case, I can’t connect to the router. The special interface for specifying the firmware file doesn’t open at the address 192.168.1.1.
For the OpenWrt firmware, you provided a special firmware for the transition. I understand that you also need a special version to return to the factory firmware.
Please help me return to the factory firmware.
Thank you for your assistance. Best regards, Dan
"
@Dear Александр,
The OpenWrt firmware is not developed by Cudy but by the developers. We need the OpenWrt forum official support the router at first, then we can release a middle firmware for you, then you can use and upgrade to the OpenWrt firmware.
For WR3000 V2.0, it is impossible to develop the OpenWrt firmware currently.
“Please tell me when the OpenWRT firmware for WR3000 V2.0 will be available.”
@Dear Андрей,
I just uploaded the intermediate firmware for WR1300S V1.0 to the Google Drive. You can download it.
“When will there be an openwrt for WR1300S ? The kernel and sysupgrade were previously sent”