OpenWrt programmatūras lejupielāde

Ubrīdinājumi

Šajā tīmekļa vietnē ir uzskaitīta ierīču programmatūra, kas atbalsta OpenWrt sistēmu, pirms lejupielādējiet un instalējiet programmatūru, lūdzu, ņemiet vērā, ka OpenWrt projekts ir Linux operētājsistēma, kas paredzēta iegultajām ierīcēm. Tā vietā, lai mēģinātu izveidot vienotu, statisku programmaparatūru, OpenWrt nodrošina pilnībā rakstāmu failu sistēmu ar pakešu pārvaldību. Tas atbrīvo jūs no ražotāja nodrošinātās lietojumprogrammu atlases un konfigurācijas un ļauj jums pielāgot ierīci, izmantojot paketes, lai tā atbilstu jebkurai lietojumprogrammai. Izstrādātājiem OpenWrt ir ietvars, kas ļauj izveidot lietojumprogrammu bez nepieciešamības ap to veidot pilnu programmaparatūru; lietotājiem tas nozīmē iespēju pilnībā pielāgot ierīci, lai to izmantotu tā, kā nekad nav iedomājušies.

Apraksts

  1. Šo failu var izmantot tikai tad, ja maršrutētājs darbojas ar Cudy tīmekļa lietotāja saskarni
    2. .
  2. Ja maršrutētājs jau darbojas ar OpenWRT UI, lietotājam vispirms jāatjauno to uz Cudy oficiālo firmware. Un pēc tam atjaunināt maršrutētāju ar šo programmaparatūru.
    3. .
  3. Kā atjaunot maršrutētāju uz Cudy oficiālo programmaparatūru? Lūdzu, izlasiet lejupielādētajā failā esošo readme.
    4. .

Garantija:

Cudy ar šo paziņo

  1. Mēs, Cudy, neuzņemamies garantiju attiecībā uz programmatūru, ko nav izlaidusi Shenzhen Cudy Technology Co., Ltd.
    2. .
  2. Mēs neuzņemamies nekādas garantijas produktiem, kuros ir instalēta jebkāda programmatūra, ko nav izlaidusi Shenzhen Cudy Technology Co., Ltd.
    3. .
  3. Ja jums ir nepieciešams izmantot openwrt programmatūru, iesakām to lejupielādēt no Cudy oficiālās vietnes.
    4. .

Saņemiet OpenWrt programmaparatūru, lai noņemtu paraksta pārbaudi: Drive

OpenWrt firmware meklētājs (nav izlaists Cudy): OpenWrt Firmware Selector

Atpakaļ uz emuāru

1530 komentāru

Hello.

I have a Cudy WR3000 V1.0 router.

Serial number starts with: 2532

Current stock firmware: 2.4.19-20250828-192837

I would like to install official OpenWrt.

Please send me the latest Cudy-signed OpenWrt intermediate firmware compatible with my WR3000 V1.0 and this hardware/flash revision.

Thank you.

Vadim

Hello,

I have a Cudy WR3000 V1.0 EU router.

Serial number starts with: 2539
Current stock firmware: 2.4.19-20250828-192837

I would like to install official OpenWrt.

Please send me the latest Cudy-signed OpenWrt intermediate firmware compatible with my WR3000 V1.0 and this hardware revision.

Thank you.

NN

Greetings,
I would like to request for the signed openwrt firmware for M3000 with a Motorcomm YT8821 (Variant 2) please.
Thanks

Davis

@Dear Mike,
The firmware file in Google Drive is correct. This is for both hardware version. Please unzip the file before update.
Note: If you have installed Mesh system with the router. You can’t update the firmware. Please power off the other Mesh device. Then reset this router to factory default. You can update this firmware before mesh system installed.

“Hi,
I would also like to request the M3000 V.2 with the Motorcomm YT8821 chip, if that’s possible.
Thank you.”

support

@Dear Горбунов Михаил,
I think there is some hardware faulty in the router. You can try to contact the seller to request a replacement and try again.

“Hello. I specifically need to install OpenWrt on a Cudy M3000 V2.0. The current issue is not simply with the stock firmware, but with the OpenWrt installation process and the intermediate firmware file.

The situation is as follows:

Router: Cudy M3000 V2.0
I used the intermediate firmware file intended for transitioning from the stock Cudy firmware to OpenWrt.
After flashing that intermediate file, the router does not boot into OpenWrt correctly.
The Ethernet connection periodically goes down and comes back up.
The router appears to enter a reboot/boot loop, with the LED changing states.
There is no stable access to OpenWrt at 192.168.1.1.
Sometimes 192.168.10.1 becomes available again.

So my goal is not just to restore the stock firmware. I need to successfully complete the installation of OpenWrt.

Could you please clarify:

After flashing your intermediate file, should the M3000 V2.0 boot directly into OpenWrt?
If yes, why might my router be entering a boot loop instead of booting OpenWrt?
Is another firmware file required after the intermediate file?
If so, which exact OpenWrt image should be used for Cudy M3000 V2.0?
Should it be a factory.bin, sysupgrade.bin, or a special recovery/install image?
If the next step must be performed via TFTP, please provide the exact procedure:
required filename;
PC IP address;
router IP address;
which LAN port to use;
RESET/power-on sequence;
which firmware image should be transferred.
Could this problem be caused by the intermediate firmware itself or by a specific hardware revision of the M3000 V2.0?

What I need is a working step-by-step procedure for installing OpenWrt on the M3000 V2.0 from its current state, because at the moment the intermediate firmware does not result in a successful OpenWrt boot.

If necessary, I can provide a video of the boot loop, ipconfig/ping output, and the current stock firmware version."

support

Atstāt komentāru