1. Lejupielādējiet un atinstalējiet failu no šeit.
2. Lejupielādējiet jaunāko programmaparatūru no oficiālās tīmekļa vietnes un pārdēvējiet to par 'recovery.bin'. Piezīme: Jums tas jāieliek tajā pašā Tftpd rīku failā.
3. Izslēdziet maršrutētāju. Atvienojiet strāvas adapteri vai nospiediet POWER pogu.
4. Savienojiet datoru ar maršrutētāja LAN portu, izmantojot Ethernet kabeli.
5. Manuāli konfigurējiet datora IP adresi "192.168.1.88".
6. Palaidiet 'tftp32.exe'.
7. Komandu rindā izpildiet 'netsh advfirewall set allprofiles state off', lai atspējotu Windows ugunsmūri, pretējā gadījumā tftp tiks bloķēts. Vai arī varat atspējot ugunsmūri datora vadības panelī. Kā parādīts tālāk.
8. Nospiediet "Atjaunināt" pogu/aizvērtni un turiet to. Pirms maršrutētājs tiek ieslēgts un pirms tftp sāk lejupielādēt programmaparatūru, neatlaidiet 'Reset' pogu/caurumu.
9. Ieslēdziet maršrutētāju.
10. Kad visas lampiņas ātri mirgo vai kad tftp sāk lejupielādēt programmaparatūru, varat atlaist "Reset" pogu/durvīti.
11. Kad lampiņa lēni mirgo, atjaunināšana ir pabeigta.
12. Lūdzu, atjaunojiet datora IP adresi, lai tā būtu dinamiskais IP.
13. Gatavs.
249 comments
hi i am having exactly the same flash issue from openwrt as alan for the 256mb cudy, i follow the instructions and download the 2.3.9. firmware for 256mb cudy tr3000. The router kept flashing red and white after going through the tftp for recovery
Ссылки не работают, судя по комментариям компания больше не хочет что бы люди пользовались их ПО?
Я хочу восстановить официальную прошивку на WR3000S, как мне это теперь сделать?
@Dear Alan,
Our technical support has contacted you via email. Please check.
“Thank you for your response. However, it did not resolve my issues.
Currently, my TR3000-256MB router when in a normal boot state. After plugging in the power cable, the red and white LEDs keep flashing, and my computer’s LAN connection is continuously going on and off. I attempted to set a static IP address of 192.168.1.2 on my computer, but I cannot ping or connect to the router’s webpage at 192.168.1.1.
When I try to use TFTP, the router does not respond to my computer’s IP (192.168.1.88), but it does respond to 192.168.1.2. After sending the recovery.bin file (downloaded from the mainland webpage: TR3000_256MB_Flash-R103-2.3.9-20250208-171917-sysupgrade.bin) to the router, it does not reboot on its own, and the LEDs continue to flash red and white.
The loop is continuous. Am I flashing the correct file? Is there any other way to restore the factory firmware?"
Thank you for your response. However, it did not resolve my issues.
Currently, my TR3000-256MB router when in a normal boot state. After plugging in the power cable, the red and white LEDs keep flashing, and my computer’s LAN connection is continuously going on and off. I attempted to set a static IP address of 192.168.1.2 on my computer, but I cannot ping or connect to the router’s webpage at 192.168.1.1.
When I try to use TFTP, the router does not respond to my computer’s IP (192.168.1.88), but it does respond to 192.168.1.2. After sending the recovery.bin file (downloaded from the mainland webpage: TR3000_256MB_Flash-R103-2.3.9-20250208-171917-sysupgrade.bin) to the router, it does not reboot on its own, and the LEDs continue to flash red and white.
The loop is continuous. Am I flashing the correct file? Is there any other way to restore the factory firmware?
@Dear Alan,
The LAN IP address will be changed from 192.168.10.1 to 192.168.1.1 after firmware update. You need to set the IP address to DHCP to get the IP address from the router.
You need to connect your computer to the LAN port of the router. Then try to login to the web page of the router via the IP address 192.168.1.1.
“Hi, I want to flash my TR300-256Mb router to OpenWrt, but after using the “cudy_tr3000-256mb-v1-sysupgrade.bin” file, it doesn’t display any pages upon reboot. The red and white LEDs keep flashing. I attempted to use TFTP for recovery, but unfortunately, I can’t revert to the original firmware. The same LED signal persists.
So, What can I do?”