Cudy Whole Home Mesh sistēma ir izstrādāta, lai novērstu nedzīvās zonas un nodrošinātu nepārtrauktu Wi-Fi savienojumu visā mājoklī. Šis raksts sniegs jums norādījumus, kā soli pa solim izveidot tīklveida sistēmu.
Pierakstīšanās:
1. Pārliecinieties, ka jums pieder vismaz 2 Cudy produkti.
2. Visi Cudy produkti atbalsta tīkla tehnoloģiju: Home Mesh-Cudy oficiālā tīmekļa vietne
3. Programmatūra ir atjaunināta:
4. Ņemiet tās vienā telpā.
5. Atiestatiet visu Cudy produktu rūpnīcas noklusējuma iestatījumus. (Ieslēdzot strāvas padevi, nospiediet un turiet nospiestu RESET pogu ar tapu 6 s, pēc tam atlaidiet.)
6. Iestatiet galveno maršrutētāju un izveidojiet tā savienojumu ar internetu.
Nākumā kā piemēru ņemam M1800 un WR2100:
1. solis: Atveriet tīmekļa pārlūkprogrammu un dodieties uz http://cudy.net vai http://192.168.10.1.
Sīkāku informāciju skatīt Kā pieteikties Cudy Router tīmekļa saskarnē?"
2. solis: Sistēmas statusa lapā noklikšķiniet uz pogas "+".
3. solis: Nospiediet WPS pogu uz M1800 un pēc tam nospiediet WPS pogu uz WR2100.
Galvenie tīkla bloki: Balta zibspuldze
Papildu tīklveida bloks: Mirgo pārmaiņus baltā un sarkanā krāsā
4. posms:Ieies "Skenēšana", pēc tam " Savienošana".
5. solis: Pagaidiet, līdz papildierīces maršrutētāja sistēmas indikators kļūst nepārtraukti zils, pēc tam pārvietojiet WR2100.
6. solis: gūstiet panākumus un izbaudiet tīkla tīkla darbību.
Piezīme:
1. 4/5G maršrutētāju var iestatīt tikai kā galveno tīkla vienību. Piemēram:
2. Jūs nevarēsiet pieteikties papildu tīkla maršrutētāja tīmekļa saskarnē. Ja vēlaties mainīt iestatījumus, noklikšķiniet uz "Sistēmas statuss"->"Mesh".
83 comments
@Dear Oli,
Cudy AP1300 can only install mesh system with Cudy product. If the speed is slow, may be there is some limit on the main router. You can try to set it to the Wireless Router mode and check.
“Recently installed an AP1300 in AP mode. Served via CAT 7 ethernet cable attached to the main internet router of the Internet Provider (diffrent brand). DIdn’t realize, that mesh is default while AP mode setup of the cudy. May mesh disturb, i.e. slow down connection of attached devices?”
Recently installed an AP1300 in AP mode. Served via CAT 7 ethernet cable attached to the main internet router of the Internet Provider (diffrent brand). DIdn’t realize, that mesh is default while AP mode setup of the cudy. May mesh disturb, i.e. slow down connection of attached devices?
@Dear Gabriel,
Basically, this is a hardware issue. May be caused by the cable or the router. We can have a compare test. You can choose one of the other two routers, Reset it and set it to be the main mesh router and connect to the same cable to check if it work on 1 Gbps or 100Mbps to judge the root cause.
“Dear Cudy Support,
I recently purchased a Cudy AX3000 Gigabit WiFi 6 Mesh Router along with two additional AX3000 mesh units, all of which support gigabit Ethernet ports.
My internet plan provides 200Mbps, and I am using undamaged Cat 6 Ethernet cables. The main router is connected to one of the mesh nodes via Ethernet. Up until yesterday, everything was working perfectly—I was getting full gigabit speeds through the LAN ports.
However, after rebooting the entire system today, the main router’s Ethernet ports are now only delivering 100Mbps. I’ve confirmed that the cables are properly seated and not damaged, and the same setup was previously delivering full gigabit speeds without issue.
Could you assist in identifying what might have caused this and how to resolve it?
Thank you"
Dear Cudy Support,
I recently purchased a Cudy AX3000 Gigabit WiFi 6 Mesh Router along with two additional AX3000 mesh units, all of which support gigabit Ethernet ports.
My internet plan provides 200Mbps, and I am using undamaged Cat 6 Ethernet cables. The main router is connected to one of the mesh nodes via Ethernet. Up until yesterday, everything was working perfectly—I was getting full gigabit speeds through the LAN ports.
However, after rebooting the entire system today, the main router’s Ethernet ports are now only delivering 100Mbps. I’ve confirmed that the cables are properly seated and not damaged, and the same setup was previously delivering full gigabit speeds without issue.
Could you assist in identifying what might have caused this and how to resolve it?
Thank you
@Dear Walter,
Yes, you can. The Cudy APs, such as the AP3000 and AP1300 can work as the main mesh device to manage other APs. You can set up one of the AP3000 and connect it to the network. Then connect other AP to the network. The mesh system will be installed automatically.
“Can I set up a mesh network using only Cudy AP’s? I have a different brand router so I want to build a mesh network with just the AP’s”