Frissítés: 2025. december 24. Jó hír!
Az OpenWrt fórum egyesítette az új Flash F50L1G41LC-t támogató csomagot és az OpenWrt firmware 24.10.5-ös verzióra frissítését. Tehát, ha a jövőben letöltöd az OpenWrt firmware 24.10.5-ös vagy újabb verzióját a Cudy-hoz kapcsolódó modellek frissítéséhez, nem lesz probléma.
Fontos közlemény: 2025. november 24.
A 2025 novemberétől gyártott Cudy AX3000 sorozatú routerek (TR3000, az sorozatszám 2543-mal vagy újabbal kezdődik. A 2543 az sorozatszámban a 2025-ös év 43. hetét jelenti) az új F50L1G41LC flash memóriát használják. Az OpenWrt köztes firmware vagy az OpenWrt firmware régebbi verzióira való frissítés megakadályozza az eszköz indítását. Ezért új firmware-frissítéseket fogunk kiadni ezekhez a termékekhez a korlátozások bevezetése érdekében. Ha a rendszer észleli, hogy az eszköz az új Flash-t használja, akkor nem lesz képes frissíteni a régebbi, 2.3.X vagy korábbi firmware-verziókra. Ezenkívül a régebbi Flash-eszközökhöz korábban biztosított OpenWrt köztes firmware nem lesz kompatibilis.
Az érintett modellek a következők: AP3000 Outdoor 1.0, AP3000 Wall 1.0, M3000 1.0/2.0, TR3000 1.0, WR3000E 1.0, WR3000H 1.0, WR3000S 1.0 és WR3000P 1.0.
A Cudy kiadta az új OpenWrt köztes firmware-eket, amelyeket frissítettek a Google Drive-ra. Kérjük, váltson az új köztes firmware-re.
Az OpenWrt firmware-rel kapcsolatban továbbra is várunk a hivatalos OpenWrt fórumra, hogy kiadjon egy, az új Flash-sel kompatibilis OpenWrt firmware-t. A megjelenés után kérjük, használja az új OpenWrt firmware-t.
Ha az SN kód kisebb, mint 2543. A régi flash kártyát használja. Nincs ilyen probléma.
Figyelmeztetések
Ez a weboldal az OpenWrt rendszert támogató eszközök szoftvereit sorolja fel. A szoftver letöltése és telepítése előtt kérjük, vegye figyelembe, hogy az OpenWrt Project egy Linux operációs rendszer, amely beágyazott eszközöket céloz meg. Ahelyett, hogy egyetlen, statikus firmware-t próbálna létrehozni, az OpenWrt egy teljesen írható fájlrendszert biztosít csomagkezeléssel. Ez mentesíti Önt a gyártó által biztosított alkalmazáskiválasztás és -konfiguráció alól, és lehetővé teszi az eszköz testreszabását csomagok használatával, hogy az bármilyen alkalmazáshoz illeszkedjen. A fejlesztők számára az OpenWrt egy keretrendszer, amely lehetővé teszi egy alkalmazás létrehozását anélkül, hogy egy teljes firmware-t kellene köré építeni; a felhasználók számára ez a teljes testreszabás lehetőségét jelenti, az eszköz eddig elképzelhetetlen módon történő használatát.
Leírás
- Ez a fájl csak akkor használható, ha az útválasztó Cudy webes felhasználói felület alatt működik.
- Ha a router már működik OpenWRT felhasználói felület alatt, akkor először vissza kell állítani a hivatalos Cudy firmware-re. Ezután frissíteni kell a routert ezzel a firmware-rel.
- Hogyan lehet visszaállítani a router hivatalos Cudy firmware-jét? Kérlek, olvasd el a letöltött fájlban található readme fájlt.
Garancia:
Cudy ezennel kijelenti, hogy
- Mi, a Cudy, nem vállalunk garanciát olyan szoftverekre, amelyeket nem a Shenzhen Cudy Technology Co., Ltd. adott ki.
- Nem vállalunk garanciát azokra a termékekre, amelyekre nem a Shenzhen Cudy Technology Co., Ltd. által kiadott szoftvert telepítettek.
- Ha openwrt szoftvert kell használnod, azt javasoljuk, hogy töltsd le a Cudy hivatalos weboldaláról.
Töltsd le az OpenWrt firmware-t az aláírás-ellenőrzés eltávolításához:Hajtás
OpenWrt Firmware Finder (nem a Cudy adta ki):OpenWrt firmware-választó
1312 hozzászólás
@Dear Support
I have already built a working OpenWrt firmware for AP1300 v1.0, based on the OpenWrt firmware for AP1300 Outdoor v1.0 (same SoC and hardware platform).
The firmware itself builds and boots, but I cannot flash it via TFTP or the web interface because the stock firmware requires a signed image.
To proceed without hardware modification (UART/SPI), I need an intermediate firmware that can be installed via the web interface and allows upgrading to a custom OpenWrt image (without signature verification).
Could you please provide such an intermediate firmware for AP1300 v1.0, or advise if there is an official way to bypass the signature check for development purposes?
Thank you.
“@Dear Bourn,
There is no OpenWrt firmware for AP1300 V1.0 currently. The OpenWrt firmware is not developed by Cudy but by the developers. We need the OpenWrt forum official support the router at first, then we can release a middle firmware for you, then you can use and upgrade to the OpenWrt firmware. "
@Dear Michael,
I see. I suggest you can try to do it by yourself. We don’t have such instructions.
“Hi Cudy Support Team , I’ve tried what you suggested – flashing older official firmware, but no luck , my Cudy WR3000 v1 is still bootlooping. Is there any firmware or recovery steps that I might perform in order to recover my router so I be able to boot into GUI ?
One more note : after flashing your firmware from Google drive or OpenWRT firmware, I’m able to enter to OpenWRT failsafe mode and access router via LAN using SSH , but from there I wasn’t able to perform system restoration steps from OpenWRT guides( I just don’t know how to do it propertly) . Thanks is advice for your support.”
@Dear A,
Our technical support has contacted you via email. Please check.
“WR3000P2550 . Can’t change to intermdiate cudy_wr3000p-v1-sysupgrade_20251119.bin: “File is invalid. Please retry.”
is it possible to get openwrt for WR3000P with new serial number?”
@Dear Bourn,
There is no OpenWrt firmware for AP1300 V1.0 currently. The OpenWrt firmware is not developed by Cudy but by the developers. We need the OpenWrt forum official support the router at first, then we can release a middle firmware for you, then you can use and upgrade to the OpenWrt firmware.
“Hello,
I own a Cudy AP1300 1.0 access point and would like to install OpenWrt.
https://www.cudy.com/products/ap1300-1-0
Could you please provide an OpenWrt firmware image without signature verification that can be installed via the stock web interface?"
Hi Cudy Support Team , I’ve tried what you suggested – flashing older official firmware, but no luck , my Cudy WR3000 v1 is still bootlooping. Is there any firmware or recovery steps that I might perform in order to recover my router so I be able to boot into GUI ?
One more note : after flashing your firmware from Google drive or OpenWRT firmware, I’m able to enter to OpenWRT failsafe mode and access router via LAN using SSH , but from there I wasn’t able to perform system restoration steps from OpenWRT guides( I just don’t know how to do it propertly) . Thanks is advice for your support.
“@Dear Michael,
You can try to recover the old firmware version. Such as the 2.0.0, 2.2.6. Please connect the LAN port when recovering the firmware.
“Hi Cudy Support Team , I have purchased cudy wr3000 v1 router at the end of y 2023 ,I’ve successpully installed openwrt on my router using intermideate Cudy firmware, that was about 2 years ago. Then year after at 2024 ,I decided to go back to Cudy’s official firmware using OpenWrt system update and latest official firware at that moment .But something went wrong ( as I understood, there was some internal flash incompatibility with newer firmwares and older routers caused by internal flash)
As for today 2026 , my WR3000 v1 router is bootlooping endlessly but I’m able to upload firmware using tftp64.
What I’ve tried:
– Uploading latest official firmware v WR3000-R31-2.4.19 via tftp64 (using WAN port and LAN1 port )
– Uploading itermideate firmware from google drive , using tftp64 via LAN1 port and WAN port ,
– Uploading latest openwrt firmware v24.10.5 using tftp64 via WAN and LAN1 port .
- Uploading openwrt kernel only firmware based on v24.10.5 via WAN and LAN1 port .
Only when uploade official Cudy firmware ,the device rebooted itself autoamtically afer 3-4 minutes. In all cases the device is bootloping after manual or automatic restart.
Do you have any suggestions ? Maybe some firwmare to restore the device ?”"