Frissítés: 2025. december 24. Jó hír!
Az OpenWrt fórum egyesítette az új Flash F50L1G41LC-t támogató csomagot és az OpenWrt firmware 24.10.5-ös verzióra frissítését. Tehát, ha a jövőben letöltöd az OpenWrt firmware 24.10.5-ös vagy újabb verzióját a Cudy-hoz kapcsolódó modellek frissítéséhez, nem lesz probléma.
Fontos közlemény: 2025. november 24.
A 2025 novemberétől gyártott Cudy AX3000 sorozatú routerek (TR3000, az sorozatszám 2543-mal vagy újabbal kezdődik. A 2543 az sorozatszámban a 2025-ös év 43. hetét jelenti) az új F50L1G41LC flash memóriát használják. Az OpenWrt köztes firmware vagy az OpenWrt firmware régebbi verzióira való frissítés megakadályozza az eszköz indítását. Ezért új firmware-frissítéseket fogunk kiadni ezekhez a termékekhez a korlátozások bevezetése érdekében. Ha a rendszer észleli, hogy az eszköz az új Flash-t használja, akkor nem lesz képes frissíteni a régebbi, 2.3.X vagy korábbi firmware-verziókra. Ezenkívül a régebbi Flash-eszközökhöz korábban biztosított OpenWrt köztes firmware nem lesz kompatibilis.
Az érintett modellek a következők: AP3000 Outdoor 1.0, AP3000 Wall 1.0, M3000 1.0/2.0, TR3000 1.0, WR3000E 1.0, WR3000H 1.0, WR3000S 1.0 és WR3000P 1.0.
A Cudy kiadta az új OpenWrt köztes firmware-eket, amelyeket frissítettek a Google Drive-ra. Kérjük, váltson az új köztes firmware-re.
Az OpenWrt firmware-rel kapcsolatban továbbra is várunk a hivatalos OpenWrt fórumra, hogy kiadjon egy, az új Flash-sel kompatibilis OpenWrt firmware-t. A megjelenés után kérjük, használja az új OpenWrt firmware-t.
Ha az SN kód kisebb, mint 2543. A régi flash kártyát használja. Nincs ilyen probléma.
Figyelmeztetések
Ez a weboldal az OpenWrt rendszert támogató eszközök szoftvereit sorolja fel. A szoftver letöltése és telepítése előtt kérjük, vegye figyelembe, hogy az OpenWrt Project egy Linux operációs rendszer, amely beágyazott eszközöket céloz meg. Ahelyett, hogy egyetlen, statikus firmware-t próbálna létrehozni, az OpenWrt egy teljesen írható fájlrendszert biztosít csomagkezeléssel. Ez mentesíti Önt a gyártó által biztosított alkalmazáskiválasztás és -konfiguráció alól, és lehetővé teszi az eszköz testreszabását csomagok használatával, hogy az bármilyen alkalmazáshoz illeszkedjen. A fejlesztők számára az OpenWrt egy keretrendszer, amely lehetővé teszi egy alkalmazás létrehozását anélkül, hogy egy teljes firmware-t kellene köré építeni; a felhasználók számára ez a teljes testreszabás lehetőségét jelenti, az eszköz eddig elképzelhetetlen módon történő használatát.
Leírás
- Ez a fájl csak akkor használható, ha az útválasztó Cudy webes felhasználói felület alatt működik.
- Ha a router már működik OpenWRT felhasználói felület alatt, akkor először vissza kell állítani a hivatalos Cudy firmware-re. Ezután frissíteni kell a routert ezzel a firmware-rel.
- Hogyan lehet visszaállítani a router hivatalos Cudy firmware-jét? Kérlek, olvasd el a letöltött fájlban található readme fájlt.
Garancia:
Cudy ezennel kijelenti, hogy
- Mi, a Cudy, nem vállalunk garanciát olyan szoftverekre, amelyeket nem a Shenzhen Cudy Technology Co., Ltd. adott ki.
- Nem vállalunk garanciát azokra a termékekre, amelyekre nem a Shenzhen Cudy Technology Co., Ltd. által kiadott szoftvert telepítettek.
- Ha openwrt szoftvert kell használnod, azt javasoljuk, hogy töltsd le a Cudy hivatalos weboldaláról.
Töltsd le az OpenWrt firmware-t az aláírás-ellenőrzés eltávolításához:Hajtás
OpenWrt Firmware Finder (nem a Cudy adta ki):OpenWrt firmware-választó
1314 hozzászólás
@Dear wahlfisch,
Still need some time. Please wait patiently.
“Dear Support, Any news regarding AP1300E Wall Firmware mid firmware without signing?”
Dear Support !
Purchased AP3000_P v1 access point.
Tried to flash according to the instructions from your website in openwrt through the transition firmware taken from you on google drive.
After flashing to the transition firmware, the access point lost access via lan cable ( wifi is not enabled ).
On the openwrt website found information:
As of jan. 2026, some devices are shipped with an alternate chip for single LAN port.
Now the access point is not available via lan or wi-fi.
What should I do to get the access point back online?I also can’t download the factory firmware via Recovery using the instructions on your website because the lan port is still not available.
Dear Support, Any news regarding AP1300E Wall Firmware mid firmware without signing?
“@Dear wahlfisch,
OK, I will do it.
““Sorry, there is no intermediate firmware for AP1300E Wall AP. The OpenWrt firmware is not developed by Cudy but by the developers. We need the OpenWrt forum official support the router at first, then we can release a middle firmware for you, then you can use and upgrade to the OpenWrt firmware”
Dear Support,
It would be easier, if you would provide some kind of intermediate firmware first (with fw signing disabled and so on)""
@Dear Marcel,
We don’t have plan to add the VLAN + SSID support on the WR3000H and WR11000.
In addition, The OpenWrt firmware is not developed by Cudy but by the developers. We need the OpenWrt forum official support the router at first, then we can release a middle firmware for you, then you can use and upgrade to the OpenWrt firmware.
“These are great devices. I’ve bought quite a few of them — around 10 units of the WR3000H and recently also a few BE11000.
What’s a bit unfortunate is that the WR3000H with OpenWrt supports VLANs for different SSIDs. The BE11000, however, understandably doesn’t have OpenWrt yet. On the other hand, the stock firmware on the BE11000 already supports assigning SSIDs to VLANs.
So the situation is a bit paradoxical: the BE11000 doesn’t have OpenWrt, while the WR3000H on stock firmware cannot assign SSIDs to VLANs (which OpenWrt can do). Because of this, users are forced to break the mesh network if they want to use VLANs properly.
It’s a bit disappointing because these are really good devices. The hardware clearly supports VLAN + SSID functionality, but unfortunately the stock firmware implementation on the WR3000H does not.
Is there any chance that VLAN + SSID support will be added to the firmware? Or do you perhaps plan to support OpenWrt on the BE11000 in the future?
I’d just like to know whether it makes sense to wait, or if I should simply move away from Cudy devices."
These are great devices. I’ve bought quite a few of them — around 10 units of the WR3000H and recently also a few BE11000.
What’s a bit unfortunate is that the WR3000H with OpenWrt supports VLANs for different SSIDs. The BE11000, however, understandably doesn’t have OpenWrt yet. On the other hand, the stock firmware on the BE11000 already supports assigning SSIDs to VLANs.
So the situation is a bit paradoxical: the BE11000 doesn’t have OpenWrt, while the WR3000H on stock firmware cannot assign SSIDs to VLANs (which OpenWrt can do). Because of this, users are forced to break the mesh network if they want to use VLANs properly.
It’s a bit disappointing because these are really good devices. The hardware clearly supports VLAN + SSID functionality, but unfortunately the stock firmware implementation on the WR3000H does not.
Is there any chance that VLAN + SSID support will be added to the firmware? Or do you perhaps plan to support OpenWrt on the BE11000 in the future?
I’d just like to know whether it makes sense to wait, or if I should simply move away from Cudy devices.