Frissítés: 2025. december 24. Jó hír!
Az OpenWrt fórum egyesítette az új Flash F50L1G41LC-t támogató csomagot és az OpenWrt firmware 24.10.5-ös verzióra frissítését. Tehát, ha a jövőben letöltöd az OpenWrt firmware 24.10.5-ös vagy újabb verzióját a Cudy-hoz kapcsolódó modellek frissítéséhez, nem lesz probléma.
Fontos közlemény: 2025. november 24.
A 2025 novemberétől gyártott Cudy AX3000 sorozatú routerek (TR3000, az sorozatszám 2543-mal vagy újabbal kezdődik. A 2543 az sorozatszámban a 2025-ös év 43. hetét jelenti) az új F50L1G41LC flash memóriát használják. Az OpenWrt köztes firmware vagy az OpenWrt firmware régebbi verzióira való frissítés megakadályozza az eszköz indítását. Ezért új firmware-frissítéseket fogunk kiadni ezekhez a termékekhez a korlátozások bevezetése érdekében. Ha a rendszer észleli, hogy az eszköz az új Flash-t használja, akkor nem lesz képes frissíteni a régebbi, 2.3.X vagy korábbi firmware-verziókra. Ezenkívül a régebbi Flash-eszközökhöz korábban biztosított OpenWrt köztes firmware nem lesz kompatibilis.
Az érintett modellek a következők: AP3000 Outdoor 1.0, AP3000 Wall 1.0, M3000 1.0/2.0, TR3000 1.0, WR3000E 1.0, WR3000H 1.0, WR3000S 1.0 és WR3000P 1.0.
A Cudy kiadta az új OpenWrt köztes firmware-eket, amelyeket frissítettek a Google Drive-ra. Kérjük, váltson az új köztes firmware-re.
Az OpenWrt firmware-rel kapcsolatban továbbra is várunk a hivatalos OpenWrt fórumra, hogy kiadjon egy, az új Flash-sel kompatibilis OpenWrt firmware-t. A megjelenés után kérjük, használja az új OpenWrt firmware-t.
Ha az SN kód kisebb, mint 2543. A régi flash kártyát használja. Nincs ilyen probléma.
Figyelmeztetések
Ez a weboldal az OpenWrt rendszert támogató eszközök szoftvereit sorolja fel. A szoftver letöltése és telepítése előtt kérjük, vegye figyelembe, hogy az OpenWrt Project egy Linux operációs rendszer, amely beágyazott eszközöket céloz meg. Ahelyett, hogy egyetlen, statikus firmware-t próbálna létrehozni, az OpenWrt egy teljesen írható fájlrendszert biztosít csomagkezeléssel. Ez mentesíti Önt a gyártó által biztosított alkalmazáskiválasztás és -konfiguráció alól, és lehetővé teszi az eszköz testreszabását csomagok használatával, hogy az bármilyen alkalmazáshoz illeszkedjen. A fejlesztők számára az OpenWrt egy keretrendszer, amely lehetővé teszi egy alkalmazás létrehozását anélkül, hogy egy teljes firmware-t kellene köré építeni; a felhasználók számára ez a teljes testreszabás lehetőségét jelenti, az eszköz eddig elképzelhetetlen módon történő használatát.
Leírás
- Ez a fájl csak akkor használható, ha az útválasztó Cudy webes felhasználói felület alatt működik.
- Ha a router már működik OpenWRT felhasználói felület alatt, akkor először vissza kell állítani a hivatalos Cudy firmware-re. Ezután frissíteni kell a routert ezzel a firmware-rel.
- Hogyan lehet visszaállítani a router hivatalos Cudy firmware-jét? Kérlek, olvasd el a letöltött fájlban található readme fájlt.
Garancia:
Cudy ezennel kijelenti, hogy
- Mi, a Cudy, nem vállalunk garanciát olyan szoftverekre, amelyeket nem a Shenzhen Cudy Technology Co., Ltd. adott ki.
- Nem vállalunk garanciát azokra a termékekre, amelyekre nem a Shenzhen Cudy Technology Co., Ltd. által kiadott szoftvert telepítettek.
- Ha openwrt szoftvert kell használnod, azt javasoljuk, hogy töltsd le a Cudy hivatalos weboldaláról.
Töltsd le az OpenWrt firmware-t az aláírás-ellenőrzés eltávolításához:Hajtás
OpenWrt Firmware Finder (nem a Cudy adta ki):OpenWrt firmware-választó
1444 hozzászólás
Hello,
I have a Cudy WR3000 V1.0 EU router.
Serial number starts with: 2539
Current stock firmware: 2.4.19-20250828-192837
I would like to install official OpenWrt.
Please send me the latest Cudy-signed OpenWrt intermediate firmware compatible with my WR3000 V1.0 and this hardware revision.
Thank you.
Greetings,
I would like to request for the signed openwrt firmware for M3000 with a Motorcomm YT8821 (Variant 2) please.
Thanks
@Dear Mike,
The firmware file in Google Drive is correct. This is for both hardware version. Please unzip the file before update.
Note: If you have installed Mesh system with the router. You can’t update the firmware. Please power off the other Mesh device. Then reset this router to factory default. You can update this firmware before mesh system installed.
“Hi,
I would also like to request the M3000 V.2 with the Motorcomm YT8821 chip, if that’s possible.
Thank you.”
@Dear Горбунов Михаил,
I think there is some hardware faulty in the router. You can try to contact the seller to request a replacement and try again.
“Hello. I specifically need to install OpenWrt on a Cudy M3000 V2.0. The current issue is not simply with the stock firmware, but with the OpenWrt installation process and the intermediate firmware file.
The situation is as follows:
Router: Cudy M3000 V2.0
I used the intermediate firmware file intended for transitioning from the stock Cudy firmware to OpenWrt.
After flashing that intermediate file, the router does not boot into OpenWrt correctly.
The Ethernet connection periodically goes down and comes back up.
The router appears to enter a reboot/boot loop, with the LED changing states.
There is no stable access to OpenWrt at 192.168.1.1.
Sometimes 192.168.10.1 becomes available again.
So my goal is not just to restore the stock firmware. I need to successfully complete the installation of OpenWrt.
Could you please clarify:
After flashing your intermediate file, should the M3000 V2.0 boot directly into OpenWrt?
If yes, why might my router be entering a boot loop instead of booting OpenWrt?
Is another firmware file required after the intermediate file?
If so, which exact OpenWrt image should be used for Cudy M3000 V2.0?
Should it be a factory.bin, sysupgrade.bin, or a special recovery/install image?
If the next step must be performed via TFTP, please provide the exact procedure:
required filename;
PC IP address;
router IP address;
which LAN port to use;
RESET/power-on sequence;
which firmware image should be transferred.
Could this problem be caused by the intermediate firmware itself or by a specific hardware revision of the M3000 V2.0?
What I need is a working step-by-step procedure for installing OpenWrt on the M3000 V2.0 from its current state, because at the moment the intermediate firmware does not result in a successful OpenWrt boot.
If necessary, I can provide a video of the boot loop, ipconfig/ping output, and the current stock firmware version."
@Dear Su King M’dik,
The firmware file in Google Drive is correct. This is for both hardware version. Our technical support has sent you the firmware via email. Please check.
“hello,
Could you send the OpenWrt firmware for the M3000 using the Motorcomm YT8821 (Variant 2) please?
I love your products, but you need to include a seperated download page for this.”