Avertissements
Cette page web répertorie les logiciels des appareils compatibles avec OpenWrt. Avant de télécharger et d'installer le logiciel, veuillez noter qu'OpenWrt est un système d'exploitation Linux destiné aux appareils embarqués. Au lieu de créer un firmware unique et statique, OpenWrt propose un système de fichiers entièrement accessible en écriture avec gestion des paquets. Cela vous libère de la sélection et de la configuration des applications proposées par le fournisseur et vous permet de personnaliser l'appareil grâce à des paquets adaptés à chaque application. Pour les développeurs, OpenWrt est le framework permettant de créer une application sans avoir à développer un firmware complet ; pour les utilisateurs, cela signifie une personnalisation complète et une utilisation de l'appareil inédite.
Description
- Ce fichier ne peut être utilisé que lorsque votre routeur fonctionne sous l'interface Web Cudy.
- Si le routeur fonctionne déjà avec l'interface utilisateur OpenWRT, l'utilisateur doit d'abord restaurer le firmware officiel Cudy, puis mettre à jour le routeur avec ce firmware.
- Comment restaurer le firmware officiel Cudy du routeur ? Veuillez lire le fichier readme dans le fichier téléchargé.
Garantie:
Cudy déclare par la présente
- Nous, Cudy, n'assumons aucune garantie pour tout logiciel qui n'est pas publié par Shenzhen Cudy Technology Co., Ltd.
- Nous n'assumons aucune garantie pour les produits sur lesquels sont installés des logiciels non publiés par Shenzhen Cudy Technology Co., Ltd.
- Si vous devez utiliser le logiciel OpenWRT, nous vous suggérons de le télécharger depuis le site officiel de Cudy.
Téléchargez le micrologiciel OpenWrt pour supprimer la vérification de signature :Conduire
OpenWrt Firmware Finder (non publié par Cudy) :Sélecteur de micrologiciel OpenWrt
1019 commentaires
@Dear Michael,
Regarding the tftpd recovering firmware method. You can refer to this article.
https://www.cudy.com/blogs/faq/how-to-recovery-the-cudy-router-from-openwrt-firmware-to-cudy-official-firmware?pos=1&_sid=b98054b19&ss=r
You can download the firmware for you router via this link.
https://www.cudy.com/pages/download-center/wr3000-1-0
“Hello Cudy Support Team ,
Maybe you have some intermediate , temporary firmware ,that I can flash to my WR3000 v1 using tftp64 so it will restore it’s state to defaults ? with memory erasing and rebuilidng the filesystem ? Thaks in advance.”
Hello Cudy Support Team ,
Maybe you have some intermediate , temporary firmware ,that I can flash to my WR3000 v1 using tftp64 so it will restore it’s state to defaults ? with memory erasing and rebuilidng the filesystem ? Thaks in advance.
“@Dear Michael,
I see. I suggest you can try to do it by yourself. We don’t have such instructions.
“Hi Cudy Support Team , I’ve tried what you suggested – flashing older official firmware, but no luck , my Cudy WR3000 v1 is still bootlooping. Is there any firmware or recovery steps that I might perform in order to recover my router so I be able to boot into GUI ?
One more note : after flashing your firmware from Google drive or OpenWRT firmware, I’m able to enter to OpenWRT failsafe mode and access router via LAN using SSH , but from there I wasn’t able to perform system restoration steps from OpenWRT guides( I just don’t know how to do it propertly) . Thanks is advice for your support.
@Dear Support
I have already built a working OpenWrt firmware for AP1300 v1.0, based on the OpenWrt firmware for AP1300 Outdoor v1.0 (same SoC and hardware platform).
The firmware itself builds and boots, but I cannot flash it via TFTP or the web interface because the stock firmware requires a signed image.
To proceed without hardware modification (UART/SPI), I need an intermediate firmware that can be installed via the web interface and allows upgrading to a custom OpenWrt image (without signature verification).
Could you please provide such an intermediate firmware for AP1300 v1.0, or advise if there is an official way to bypass the signature check for development purposes?
Thank you.
“@Dear Bourn,
There is no OpenWrt firmware for AP1300 V1.0 currently. The OpenWrt firmware is not developed by Cudy but by the developers. We need the OpenWrt forum official support the router at first, then we can release a middle firmware for you, then you can use and upgrade to the OpenWrt firmware. "
@Dear Michael,
I see. I suggest you can try to do it by yourself. We don’t have such instructions.
“Hi Cudy Support Team , I’ve tried what you suggested – flashing older official firmware, but no luck , my Cudy WR3000 v1 is still bootlooping. Is there any firmware or recovery steps that I might perform in order to recover my router so I be able to boot into GUI ?
One more note : after flashing your firmware from Google drive or OpenWRT firmware, I’m able to enter to OpenWRT failsafe mode and access router via LAN using SSH , but from there I wasn’t able to perform system restoration steps from OpenWRT guides( I just don’t know how to do it propertly) . Thanks is advice for your support.”
@Dear A,
Our technical support has contacted you via email. Please check.
“WR3000P2550 . Can’t change to intermdiate cudy_wr3000p-v1-sysupgrade_20251119.bin: “File is invalid. Please retry.”
is it possible to get openwrt for WR3000P with new serial number?”