Avertissements
Cette page web répertorie les logiciels des appareils compatibles avec OpenWrt. Avant de télécharger et d'installer le logiciel, veuillez noter qu'OpenWrt est un système d'exploitation Linux destiné aux appareils embarqués. Au lieu de créer un firmware unique et statique, OpenWrt propose un système de fichiers entièrement accessible en écriture avec gestion des paquets. Cela vous libère de la sélection et de la configuration des applications proposées par le fournisseur et vous permet de personnaliser l'appareil grâce à des paquets adaptés à chaque application. Pour les développeurs, OpenWrt est le framework permettant de créer une application sans avoir à développer un firmware complet ; pour les utilisateurs, cela signifie une personnalisation complète et une utilisation de l'appareil inédite.
Description
- Ce fichier ne peut être utilisé que lorsque votre routeur fonctionne sous l'interface Web Cudy.
- Si le routeur fonctionne déjà avec l'interface utilisateur OpenWRT, l'utilisateur doit d'abord restaurer le firmware officiel Cudy, puis mettre à jour le routeur avec ce firmware.
- Comment restaurer le firmware officiel Cudy du routeur ? Veuillez lire le fichier readme dans le fichier téléchargé.
Garantie:
Cudy déclare par la présente
- Nous, Cudy, n'assumons aucune garantie pour tout logiciel qui n'est pas publié par Shenzhen Cudy Technology Co., Ltd.
- Nous n'assumons aucune garantie pour les produits sur lesquels sont installés des logiciels non publiés par Shenzhen Cudy Technology Co., Ltd.
- Si vous devez utiliser le logiciel OpenWRT, nous vous suggérons de le télécharger depuis le site officiel de Cudy.
Téléchargez le micrologiciel OpenWrt pour supprimer la vérification de signature :Conduire
OpenWrt Firmware Finder (non publié par Cudy) :Sélecteur de micrologiciel OpenWrt
1469 commentaires
Hello,
I have a Cudy WR3000 V1.0 EU router.
Serial number starts with: 2539
Current stock firmware: 2.4.19-20250828-192837
I would like to install official OpenWrt.
Please send me the latest Cudy-signed OpenWrt intermediate firmware compatible with my WR3000 V1.0 and this hardware revision.
Thank you.
Greetings,
I would like to request for the signed openwrt firmware for M3000 with a Motorcomm YT8821 (Variant 2) please.
Thanks
@Dear Mike,
The firmware file in Google Drive is correct. This is for both hardware version. Please unzip the file before update.
Note: If you have installed Mesh system with the router. You can’t update the firmware. Please power off the other Mesh device. Then reset this router to factory default. You can update this firmware before mesh system installed.
“Hi,
I would also like to request the M3000 V.2 with the Motorcomm YT8821 chip, if that’s possible.
Thank you.”
@Dear Горбунов Михаил,
I think there is some hardware faulty in the router. You can try to contact the seller to request a replacement and try again.
“Hello. I specifically need to install OpenWrt on a Cudy M3000 V2.0. The current issue is not simply with the stock firmware, but with the OpenWrt installation process and the intermediate firmware file.
The situation is as follows:
Router: Cudy M3000 V2.0
I used the intermediate firmware file intended for transitioning from the stock Cudy firmware to OpenWrt.
After flashing that intermediate file, the router does not boot into OpenWrt correctly.
The Ethernet connection periodically goes down and comes back up.
The router appears to enter a reboot/boot loop, with the LED changing states.
There is no stable access to OpenWrt at 192.168.1.1.
Sometimes 192.168.10.1 becomes available again.
So my goal is not just to restore the stock firmware. I need to successfully complete the installation of OpenWrt.
Could you please clarify:
After flashing your intermediate file, should the M3000 V2.0 boot directly into OpenWrt?
If yes, why might my router be entering a boot loop instead of booting OpenWrt?
Is another firmware file required after the intermediate file?
If so, which exact OpenWrt image should be used for Cudy M3000 V2.0?
Should it be a factory.bin, sysupgrade.bin, or a special recovery/install image?
If the next step must be performed via TFTP, please provide the exact procedure:
required filename;
PC IP address;
router IP address;
which LAN port to use;
RESET/power-on sequence;
which firmware image should be transferred.
Could this problem be caused by the intermediate firmware itself or by a specific hardware revision of the M3000 V2.0?
What I need is a working step-by-step procedure for installing OpenWrt on the M3000 V2.0 from its current state, because at the moment the intermediate firmware does not result in a successful OpenWrt boot.
If necessary, I can provide a video of the boot loop, ipconfig/ping output, and the current stock firmware version."
@Dear Su King M’dik,
The firmware file in Google Drive is correct. This is for both hardware version. Our technical support has sent you the firmware via email. Please check.
“hello,
Could you send the OpenWrt firmware for the M3000 using the Motorcomm YT8821 (Variant 2) please?
I love your products, but you need to include a seperated download page for this.”