What is Access Point Mode?
Access Point mode is the router uses a wired connection to the primary router or modem router to expand the wireless coverage for a home network.
Common network topology:
Step 1: Open a web browser and go to http://cudy.net or http://192.168.10.1.
For details, please refer to How to log into the web interface of Cudy Router?
Step 2: The Quick Setup window will pop up, choose 'Wireless Access Point', then click 'Next'.
Step 3: Choose your 'Time Zone'.
Step 4: Confirm the hardware connection.
Step 5: Change the wireless network name and password.
Step 6: Click "Save & Apply" to complete the configuration.
Step 7: Wait a few seconds for the system rebooting, when the login page pops up again, you can enjoy the internet.
Note:
After setting up the Cudy router into Access Point mode, the IP address will be assigned by the host router and the default IP Address 192.168.10.1 will not able to log in. If you need to log into Cudy router again, type 'http://cudy.net' into your browser or look up the Cudy router's IP address in your main (primary) router's client list.
68 comments
Estimado Antonio: ¿Qué versión de firmware tiene tu router? Cuando ocurre el problema, ¿puedes acceder a la interfaz web de tu router? Si es así, descarga el archivo de diagnóstico (archivo .bin) desde la sección «Diagnostic Tools» (Herramientas de diagnóstico) -> «Diagnosis» (Diagnóstico) -> «GO» -> «Download» (Descargar) y envía dicho archivo a supportcudy.com.
Lo revisaremos e intentaremos encontrar una solución.
“Buenas, tengo un problema similar a otros comentarios al configurar el router como access point. La conexión no es estable, hay cortes, me dice que no hay Internet, me da error al conectar, etc. He seguido los pasos correctamente, va conectado de el router de la operadora por cable, desactivé el DHCP como habéis comentado antes a otro, y no consigo solucionarlo. Mi router es un WR1500”
Buenas, tengo un problema similar a otros comentarios al configurar el router como access point. La conexión no es estable, hay cortes, me dice que no hay Internet, me da error al conectar, etc. He seguido los pasos correctamente, va conectado de el router de la operadora por cable, desactivé el DHCP como habéis comentado antes a otro, y no consigo solucionarlo. Mi router es un WR1500
@Dear Christopher,
Our technical support has sent you the solutions via email. Please check.
“Hello. I purchased a WR3600 Wi-Fi 7 unit (though the box says “BE”). I bought it primarily to use as an access point (AP), connecting it via Ethernet to my PC. When I reset the device, the network works reasonably well; however, once I configure it as a wireless access point, I run into internet connectivity issues. The Wi-Fi signal keeps dropping and reappearing, often showing “no internet,” and the Ethernet connection also experiences intermittent drops. What can I try to get it working properly? So far, the only thing I’ve attempted is disabling the DHCP server, as suggested in another comment. I’m not sure why the network keeps dropping out—any advice would be appreciated. Thanks!”
Hello. I purchased a WR3600 Wi-Fi 7 unit (though the box says “BE”). I bought it primarily to use as an access point (AP), connecting it via Ethernet to my PC. When I reset the device, the network works reasonably well; however, once I configure it as a wireless access point, I run into internet connectivity issues. The Wi-Fi signal keeps dropping and reappearing, often showing “no internet,” and the Ethernet connection also experiences intermittent drops. What can I try to get it working properly? So far, the only thing I’ve attempted is disabling the DHCP server, as suggested in another comment. I’m not sure why the network keeps dropping out—any advice would be appreciated. Thanks!
@Estimado Eliasaf:
¿Cuál es el modelo de tu producto Cudy? ¿Cómo quieres utilizarlo?
“Me sale mal porque no se configurarlo”