1. Laadige fail alla ja pakendage see hinnast.
2. Laadige uusim püsivara ametlikust veebisaidist ja nimetage see ümber "recovery.bin". Märkus: Te peate selle panema samasse faili Tftpd tööriistade hulka.
3. Lülitage ruuter välja. Tõmmake toiteadapter välja või vajutage nuppu POWER.
4. Ühendage arvuti ruuteri LAN-porti Ethernet-kaabliga.
5. Konfigureerige oma arvuti IP-aadressi '192.168.1.88' käsitsi.
6. Käivitage 'tftp32.exe'.
7. Käivita käsureas 'netsh advfirewall set allprofiles state off', et keelata Windowsi tulemüür, muidu blokeeritakse tftp. Või lülitage tulemüür välja oma arvuti juhtpaneelis. Nagu allpool näidatud.
8. Vajutage nuppu/auku "Reset" ja hoidke seda all. Enne ruuteri sisselülitamist ja enne, kui tftp alustab püsivara allalaadimist, ärge vabastage nuppu 'Reset' / auku.
9. Lülitage ruuter sisse.
10. Kui kõik tuled vilguvad kiiresti või kui tftp hakkab püsivara alla laadima, võite vabastada nupu 'Reset' nuppu/auku.
11. Kui tuli vilgub aeglaselt, on uuendamine lõpetatud.
12. Taastage oma arvuti IP-aadress dünaamiliseks IP-ks.
13. Valmis.
142 comments
@Уважаемый Владм!
Пожалуйста, следуйте этой инструкции, чтобы восстановить заводскую прошивку Cudy WR300.
Для чего нужен пароль?
“Как прошить обратно cudy wr300 на заводскую прошивку?
Пишите где ввод пароля (неверная информация)”
@Dear kozian,
For TR1200, there is a difference. You must connect your computer to WAN port of TR1200 when recovering. For TR3000, you must connect your computer to LAN port of TR1200 when recovering. Please have a check.
“@Support
>> Did you change the uboot when you update the OpenWrt firmware?
No, i did not.
I was able to restore TR3000 using another mac. I used external ethernet dongle and it seems it took to long to bring interface up. Mac mini with internal ethernet did the job fine.
With TR1200 that was not an issue btw! Perhaps due to it’s lower cpu and longer time to boot."
Как прошить обратно cudy wr300 на заводскую прошивку?
Пишите где ввод пароля (неверная информация)
@Support
>> Did you change the uboot when you update the OpenWrt firmware?
No, i did not.
I was able to restore TR3000 using another mac. I used external ethernet dongle and it seems it took to long to bring interface up. Mac mini with internal ethernet did the job fine.
With TR1200 that was not an issue btw! Perhaps due to it’s lower cpu and longer time to boot.
@Dear kozian,
Did you change the uboot when you update the OpenWrt firmware? Please tell me the steps when you update the OpenWrt firmware.
“Trying to restore official firmware on TR3000 V1 (after OpenWRT). Router does not connect to tftp server. `tcpdump arp` shows no requests from router either. Used 192.168.1.88 / 192.168.1.2 / 192.168.10.88 IP for server, Lan port. LED blinks red-white.
Need help.”